The Wet Equalizer Bolt with Locknut and Grease Zerk # 126B2 and Bronze Bushing # D014-077-00 can be used to replace the wet bolts that are frozen on your 2020 Grand Design Momentum 351M.
The wet bolts on the Momentum were most likely not serviced properly from the dealer/owner of the camper is my guess. If water got into the bushings and caused rust to develop this is what I feel may be causing you to not be able to install grease into the bolt. Typically the grease zerk will be the first... view full answer...
I believe what you are asking about is the hall effect sensor. Yes, the Replacement 24-1/2" Left Rear Leg - Lippert Ground Control 3.0 Electric Leveling System # LC305339 does have the hall effect sensor in it. Assuming you have the Lippert Ground Control 3.0 automatic leveling system # LC358590 or # LC675817 this is the replacement leg you are looking for. view full answer...
The Replacement Stainless Steel Top with Glass Cover for Furrion 2-in-1 Range Oven # C-FSRE21SA-SS-003 is designed to fit Furrion models FSRE17SASS, F1S21L02A-SS, or FSRE21SASS. The part number you have there, FDO12A-SS, is actually the Front Panel for Furrion 2-in-1 Range Oven Drawer. The front panel corresponds with some of the same range ovens, but not all of them so I can't confirm if it will work based on that part number. If you find that you have one of these model numbers then this... view full answer...
There are a couple possible grease seal sizes for the hubs on your Grand Design 6,000 pound Dexter axles, so the only sure way to determine the right one will be to pull one the hub assemblies and take a look at the existing seal. There should be a number stamped on the seal itself identifying its size, but if it's too worn you can also measure the outer diameter of the spindle where it sits (or the diameter of the seal if it's in good enough condition).
Most likely you will need either... view full answer...
I looked up the specs of the Flojet 030526144 and they are 2.9 gallons per minute and 50 PSI. The HydroMax RV Fresh Water Pump # P25201 is 3 gallons per minute and 55 PSI.
The HydroMax will work as a replacement water pump for your 2015 Grand Design Reflection. It mounts in any direction so installation should not be major reconstruction. view full answer...
It sounds like you currently have the older Replacement Basic Wall Thermostat for Furrion Chill RV Air Conditioner - Single Zone - Black FACW12SA-BL. You can indeed change it out for the Premium Wall Thermostat for Furrion Chill RV Air Conditioner - Single Zone - Black # FR33PR. I included a demonstration video for you. view full answer...
You can use the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS to replace your damaged 10A04751ksz MaxxAir circuit board. This is a direct replacement. view full answer...
From what I have found, the GVWR of your 2020 Grand Design Imagine XLS 22RBE is 6,995 lbs. Based on that information, you more than likely have 3,500 lb axles. The most common grease seal for a 3,500 lb axle is the # 58846 with a 1.719" inner diameter and 2.565" outer diameter. For a pair you would need the # RG06-050.
This is strictly based on your typical 3,500 lb axle. Ultimately there is no way to be sure without identifying the axle or the part number on the grease seal. If you are... view full answer...
Although the exact 12 inch hose is not available separately of the Camco RV and Marine Premium Water Filter # CAM40631, it is simply a standard garden hose connection so what you can do is use the Camco RV Drinking Water Hose # CAM22763. This hose is longer, at 4 feet, but will work as an extension hose. view full answer...
Replacement Pitch Arm Assembly for Solera XL 63" Flat Awning Support Arm - Black # LC67VR is 63 inches as stated. That is the total length of the assembly. The parts department at Lippert who makes Solera couldn't give me the individual dimensions of the parts that are bolted together, so you will need to measure your assembly in the same way with the parts combined at straight length to determine compatibility. view full answer...
The Furrion Replacement 5" Monitor # FR97FR is going to be specific to the Vision S series of cameras. If you have the older Vision or Vision II you will need to upgrade to the Furrion Vision S Wireless RV Observation Camera System # FCE48TASL-05. Furrion discontinued the older cameras and monitors so there are no generic replacements. view full answer...
The Global Link RV Baggage Door Slam Latch, # 295-000015, is a replacement to Global Link, Fastec (FIC), Bauer, and Lippert Components standard baggage door lock. These are the primary vendors to most all OEM RV builders. The dimension of this particular lock is 5" wide x 4-1/2" tall x 1-1/2" thick. If the lock on your 2021 Grand Design Imagine Travel Trailer has markings showing to be produced by one of these manufacturers and meet these dimensions, then yes this will work as a replacement... view full answer...
Unless your Equa-Flex Cushioned Equalizers # LC279688 are worn out or damaged you would only need to replace the Shackle Kit # MR58ZR on your 2014 Grand Design Solitude 369RL. I do not see that your current equalizers are damaged they only appear to have surface rust. If you can see any damage to the rubber cushioning or severe rust then they should be replaced as well. view full answer...
Your 2021 Grand Design Reflection 240RL will use the Grease Seals # RG06-050. The Seal Puller # PTW1219 makes removing the seals a simple task. I recommend the LubriMatic LMX Industrial Strength Grease # L11390 for the bearings. This grease is formulated to work in both hot and cold temperatures under extreme pressures.
I do recommend having some spare bearings and races incase you discover that any are damaged.
Inner Bearing # L68149
Inner Race # L68111
Outer Bearing # LM67048
Outer... view full answer...
The Cheetah is one of the many designs that has been discontinued by Lionshead. Although we do have the 14" x 5" the 15" version is no longer available. I understand this can be frustrating, especially when your trailer is not very old. The closest design we have is the Aluminum Viking Series Vor Trailer Wheel # AX02550545FPS which is a 15" x 5" wheel. This would be fine if you're just looking for a spare, or if you want to replace all of the wheels to match. For 15" x 6" we have the #... view full answer...
I can certainly point you in the right direction. Looking at these 2020 Grand Design Imagine campers, the clearance light appears to be very similar to the Optronics # MCL0032ABB. This is a 4" long 2" tall and 1" thick amber clearance light with a black base. We also have it available with a while base # MC32AB. If you can measure one of your clearance lights, you may find that this light is virtually identical.
If you find that a different size light is needed, feel free to send me some... view full answer...
From the information I was able to see online it looks like your 2019 Grand Design Momentum 381M has 7,000 lb axles which means you should be able to use Grease Seals 10-36 (pair) # RG06-070 that you were looking at.
You will want to confirm this on your end though as well. The 10-36 grease seals have an inner diameter of 2.250" and an outer diameter of 3.376" so if you take a digital caliper and measure your spindle and current hub/drums where the seal rides you'll be able to confirm... view full answer...
No, the etrailer # e28SR would not work for your 2017 Grand Design Reflection with 5,200lb axles.
To find the correct spring you need to jack up one side of the trailer so there is no weight on the spring at all, as weight will make the spring get longer, and then measure from center of eye to center of eye.
If the 26" measurement is with weight on the spring, then there's a good chance you'll instead need the # e76SR instead which has a 5,300lb rating and measures 24-7/8" long.
Let... view full answer...
There unfortunately isn't a package for just the rotors and brake pads together so you would need to purchase the rotors and pads separately in order to avoid paying for new calipers as well. To find the correct rotors we'll need a bit of information first. We'll need to know your current stud size and the bearing/seal item numbers if you have an hub with an integrated rotor.
If you remove the hub/rotor you can take a look at the outer bearing and the grease seal to see if the item number... view full answer...
Go To Results