The Blue Ox TrackPro Weight Distribution Systems like part # BLU77FR have four points of sway control, two in the hitch head and one on each frame bracket. It provides excellent sway control and sway prevention. It has a lifetime warranty, is made in the USA, and has a pre-torqued hitch ball for minimal assembly. view full answer...
I'd first check the pins of the adapter for corrosion and clean as necessary with sandpaper as that's normally what causes issues with circuits not being active. Next thing to look for is bent pins or broken wire on the adapter but I'd be shocked if the issue wasn't corrosion. view full answer...
The Tekonsha BRAKE-EVN # TK63VR and the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long # 20127 will work with your 2014 Toyota Tundra.
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118496 will connect to your factory wiring and then the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires # ETBC7 to give you the 7-way with brake controller wiring. view full answer...
At this time yes the RoadActive Suspension kit part # RAS4611TD does fit all models of the 2007-2021 Toyota Tundra. It might be fit for newer models too going forward but this is as of September 2021. view full answer...
The best weight distribution for towing a Keystone Springdale with a tongue weight of 530 lbs is the Reese Strait Line part # RP66083 which has a tongue weight range of 400-800 lbs and features best sway control at preventing sway before it starts.
For a similar Blue Ox kit to the one that you referenced that would be the correct rating you'd want the part # BLU82XR which is rated for tongue weights between 500-800 lbs. view full answer...
Sounds like you are looking for a fifth wheel rail kit for your 2017 Toyota Tundra short bed. For that we have the Reese custom install kit part # RP50084-58. The custom rail kits are preferred as they install in much less time than a universal kit and minimize drilling.
Since you have a short bed you'd need a slider hitch like the Reese # RP30047. view full answer...
I assume that you are wanting a 3 inch rise or drop ball mount for your factory installed 2012 Toyota Tundra with a factory installed Class IV hitch that has a 2 inch receiver. You have indicated that you would prefer a ball mount that is made of all aluminum or stainless steel components, has an anti-rattle device and is lockable. Unfortunately, we do not have a fixed stainless steel or aluminum draw bar that will provide a 3 inch drop or rise. However, we do offer several options for... view full answer...
The Husky Center Line Weight Distribution System w/ Sway Control # HT32218 referenced in your question includes a torqued 2-5/16 inch hitch ball. If you are needing a 2 inch hitch ball instead, you will just need to add one with a compatible shank like the Curt # A-90.
This is a really nice weight distribution system that has tongue weight capacity of 800 to 1,200 pounds. When choosing a properly rated system, you will want to consider the total tongue weight of your towing setup. This... view full answer...
Yes the Curt weight distribution system part # C24UR that you referenced is compatible with the hitch of your 2018 Toyota Tundra SR5. view full answer...
I have an option that may work for you, but the only Class IV trailer hitch receiver available for your 2006 Toyota Tundra is the Draw-Tite Trailer Hitch Receiver - Multi Fit - Class IV - 2" # 37130 but it will not fit your 2006 Toyota Tundra if you have the factory towable bumper due to the bumper supports being in the way of the hitch. It may be possible to replace the towable bumper on your Tundra with a standard bumper which would allow you to use the # 37130.
At this time we do not... view full answer...
You are going to need the Tekonsha brake controller harness part # 3031-P. The white end of this connector will plug into the port under the dash of your truck and then to attach the harness to your brake controller you will need to cut off the black end and hardwire it to your controller.
Hopkins doesn't have a harness at this time for your vehicle, but this harness will work just fine. view full answer...
The Redarc Tow Pro Liberty part # RED24FR is a fit for your 2010 Toyota Tundra and would work great in your 2010 Toyota Tundra. You'd just need two install harnesses part # 3040-P and # 331-TPH-017 then you'd be set. view full answer...
If you check out the install video I attached you can see that when we installed a brake controller in a 2013 Toyota Tundra like yours we attached the ground to the parking brake bracket. Fast forward to the 1:20 mark of the video to see exactly where. view full answer...
We do sell combination oil/transmission coolers. Check out the Derale Combination Transmission and Engine Oil Cooler # D15902. This is a single unit that has two sections, one for cooling transmission fluid and the other for cooling engine oil.
I did some checking and this cooler does come with a fitting that is compatible with the oil filter on your 2008 Toyota Tundra so it should work very well for you.
The kit does come with generic installation instructions that will detail how to... view full answer...
Seems like you have the Extang Trifecta 2.0 # EX92461 on your 2015 Toyota Tundra. This is an above the rail tonneau cover so the stake pockets are covered. There really is not a ladder rack that you can use with the tonneau cover you have.
If you're really wanting a tonneau and ladder rack combo you have some options. The highest tier setup would be the RetraxPRO XR # RTT-80841 and then you can use the Yakima OverHaul HD system # Y01151-5855 that will fit in the T-Slots in the RetraxPRO... view full answer...
For a ladder rack to fit in the channels of the RetraxPRO XR tonneau cover part # RTT-80833 that you have on your 2021 Toyota Tundra long bed you'd want the Yakima Overhaul HD ladder rack with tonneau cover adapter # Y01151-5855 and you'd be set. view full answer...
Great choice on the BAK Revolver X4s Hard Tonneau Cover # BAK46ZR for your 2021 Toyota Tundra, it is one of my favorites.
For a ladder rack you can either use the Adarac Pro Series # A4001666 or the Thule TracRac SR # TH97RV since they mount on top of the bed rails. All of the other ladder racks use a clamping system that won't work with your tonneau cover since the cover is in the way of where the clamps will go.
I prefer the TracRac SR over the Pro Series because it's easier to adjust... view full answer...
The install instruction of the Magnaflow Kit part # MF15306 make no mention of the spare tire so you would be able to keep yours and install this kit.
Now it's nearly impossible for me to know if the kit would fit with a 35 inch wheel and tire combo since this has only been tested with the factory spare size.
This is a fit for your 2017 Toyota Tundra double cab with a 5.7 liter engine and 6-1/2 foot bed. view full answer...
Thank you for all of the information! The Rola Haul-Your-Might T3 # 59799 will do a good job at helping you to transport your kayaks with your 2022 Toyota Tundra.
The best saddle-style kayak carrier is the Yakima SweetRoll # Y04074 because it comes with tie-downs, it's easy to install, and the rear saddles have integrated rollers so you will have an easier time loading your kayaks. For extra protection you can lock all of the saddles to your ladder rack we have the 8 Core Kit # Y07208... view full answer...
There is one slider fifth wheel hitch that will slide far enough to allow a 5-1/2 foot bed to make sharp turns. For that we have the Demco Hijacker part # DM8550040 which will automatically slide 22-1/2 inches as you turn. For a fifth wheel rail kit the part # DM8552020-71 is a fit for your 2014 Toyota Tundra short bed as well.
This hitch has a 13k capacity also. view full answer...