For your 2011 Keystone Hornet, you can use the Single Rocker Switch # 37212635 in white, or # 37212625 in black to in two different locations to create a 3-way switch that can be controlled in separate locations. view full answer...
There is a wet bolt kit made specifically for a tandem axle trailer with Road Armor equalizers, and includes the shackles, wet bolts, and hardware needed. What you need is the following part:
- Lippert AP Kit - Tandem Axle Road Armor Wet Bolts and Shackles # LC52SV
If you need new bushings as well you can use the Bronze Bushings - Qty. 4 # K71-291-00. view full answer...
I was not able to locate anything on that part number, however since you have a 2016 model year trailer there is a good chance the awning was made after 2015 in which you'd need the Replacement Motor for Solera Power RV Awnings Manufactured after 2015 # LC373566.
If it turns out the motor was made prior to 2015, then you'd want the Replacement Motor for Solera Power RV Awnings Manufactured before 2015 # LC266149 instead. view full answer...
You can replace the arms on your Dometic manual pull down awning with electrical arms, which is usually a much more convenient and cost effective option than replacing the entire awning itself. To replace the arms you can use either part # LC434723 for Black or part # LC434724 for White, which are 69" awning arms that will connect to your existing awning setup and are powered through your RV battery.
There is also a version of this upgrade that comes with it's own 18v battery, which are... view full answer...
I have a solution for you, but it looks like the 2021 Keystone Cougar 34TSB is 37'-5", so the Adco # 290-52247 is going to be just a hair too short for this trailer. Instead I recommend using the Adco SFS AquaShed RV Cover for Toy Hauler Travel Trailer - Up to 40' Long - Gray # 290-52277, which will fit well on your Cougar Half-Ton. The SFS AquaShed provides great protection from the elements, and the fabric helps prevent moisture from pooling on the cover during storage.
I've linked... view full answer...
We don't have a database that tells us what the stud size is on that hub, but I was able to do a little bit of research and find some reports that say that your 1/2" thread by 2" long stud seems to be accurate. For that size wheel stud you can use the Redline # 7-122 lug studs you were looking at which are 2" long and have 1/2" threads. view full answer...
We do have a variety of lift kits that can possibly work with the tandem axles on your 2005 Keystone Zeppelin. If you're needing just a little lift then the Tandem Axle Lift Kit # RR23QX will give you up to 2-1/4" of lift.
For something a little more substantial you can install an over-under conversion kit (as long as your axles are currently ABOVE your leaf springs). Use kit # K71-384-00 for a 2-3/8" axle or kit # K71-385-00 for a 3" axle.
The conversion kits will increase the height... view full answer...
I have a solution for you, but I'm not aware of any way to convert a Keystone factory cargo carrier into a hitch receiver. However, you can use a universal hitch like the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703 on your 2018 Keystone Cougar 359MBI to add a 2" receiver with a 350-lbs tongue weight capacity, so it's perfect for a Swagman Escapee.
The Curt # 13703 can be bolted or welded onto box frame, C-channel frame, or I-beam frame trailers where the... view full answer...
If you're talking about the actual lid for the vent then you can use the MaxxAir UniMaxx Universal Replacement Lid # MA00-335002 as a replacement no matter the brand vent you have. This lid has a universal fit hinge that will mount to your current vent.
If you're looking for the cover that sits above the vent and will allow you to use the vent in inclement weather or while traveling then you're looking for the MaxxAir II RV and Trailer Roof Vent Cover w/ EZClip - Black # MA86JR. This... view full answer...
For your 2006 Keystone Everest 364Q, with a 20' awning, you can use the:
-Solera Classic Universal Awning Support Arms for RVs - 68" to 81" Arms - White # LC434718,
-Solera Classic Universal Awning Support Arms for RVs - 81" to 96" Arms - White # LC434720,
Or The
-Solera Classic Universal Awning Support Arms for RVs - 68" to 81" Arms - Black # LC434717,
-Solera Classic Universal Awning Support Arms for RVs - 81" to 96" Arms - -Black # LC434719.
You'll just need to measure the length... view full answer...
The Replacement Charger for Lippert Ground Control 3.0 Touchscreen Remote # LC267401 is the correct part needed to charge the touchscreen remote on your 2021 Keystone Sprinter Limited.
Replaces the wall charger for the touchscreen remote originally included with Lippert Ground Control 3.0 automatic leveling system (LC358590 or LC675817).
If you have any further questions please feel free to reach back out to me anytime and I would be more than happy to further assist you. view full answer...
The closest thing I was able to find that is to what you're looking for is the:
-Trailer Wheel Center Cap Plug # AM90081.
This wheel center plug will fit center caps that have an outer diameter of 2.95" to 5.15", has an O.D of 2-1/16", and is made from ABS plastic. view full answer...
In order to re-pack the bearings on your trailer, all you will need is the grease, bearing packer, and grease gun:
- LubriMatic LMX Industrial Strength Grease - 14 oz. Cartridge # L11390
- Powerbuilt Deluxe Bearing Packer # ALL647646
- LubriMatic Standard-Duty, Lever Action Grease Gun # L30200
While you can certainly do it by hand, that isn't the most effective or efficient way. Otherwise, these will be the only things you need in order to pack the bearings on your trailer; I have added... view full answer...
You can piece out the Curt TruTrack Weight Distribution System # C17500 with the following part numbers that include everything but the shank:
Trunnion Spring Bar - # C17536 (need 2 of these)
Spring Bar Lift Tool - # C17512
Frame Brackets - # C17508
Replacement Head - # C17507
Hardware Kit - # C17550
2" Hitch Ball - # 63018 or 2-5/16" Hitch Ball # C40085
This is slightly more cost-effective than purchasing the whole assembly, but also keep in mind that the assembly comes with the shank.... view full answer...
We have a couple of potential options for you, however, we do not have any 9" square jack pads that you're needing.
The closest square jack pad we have is the Replacement Pad for SnapPad Jack Stand Pad System # SN37FR. This jack pad will fit an 8" square jack foot, and measures 11-1/2" in diameter.
Alternatively, we do also offer the Replacement Pad for SnapPad Jack Stand Pad System # SP54FR. Which will fit 9" round jack feet, and measures 11" in diameter. view full answer...
For your 2017 Keystone Passport, I recommend the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703. This adjustable trailer receiver hitch will work well for you because its designed for use on trailers like your Keystone Passport and can be bolted to the vehicle frame or welded on for a no-drill application. The maximum tongue weight capacity is up to 350 lbs, and the maximum gross trailer weight capacity is up to 3,500 lbs. (Confirm the trailer hitch weight capacity... view full answer...
To find out if The Road Armor Shock Absorbing Equalizer Kit # LC696740 will fit on your 2020 Keystone Cougar Travel trailer you will have to take a couple of measurements on your current equalizers. The Road Armor kit has a width of 6 inches from hole to hole on center, and a height of 3-1/4 inches from the two bottom holes to the top hole.
If your current equalizers on your 2020 Keystone match then these would work perfectly. Using this system will also provide an improved ride on your... view full answer...
The Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter w/ Offset # CAB-C5GX1216 will work great with your 2022 Ford F-450 with the factory gooseneck prep package.
This adapter has a maximum towing capacity of 20,000lbs, a maximum pin weight capacity of 4,000lbs, and is designed to work with 2-5/16" gooseneck hitch balls.
Please note also that if your factory prep package has a hitch ball with an integrated locking lever, that this kit is not recommended for use.
I have also included... view full answer...
Yes, we can help. We have an Optronics RV Scare Light, Item # RVSL31, that comes with a clear lens and white metal base. I have attached a link to a review video for you to check out. view full answer...
Yes. You can rebuild the # LC178652 (follow leg) and # LC178653 (lead leg) with part # LC146059 for the lead leg and part # LC146060 for the follow leg. view full answer...
Go To Results