The width of the Optronics LED Off-Road Light Bar - 6,777 Lumens part # UCL22CB is 30 7/8" wide without the mounting bracket s attached. view full answer...
The Blazer LED Off-Road Warning Light Bar item # BL33VR does not come with a wiring harness. It has to be purchased separately. The wiring harness includes a switch for changing the colors and turning on and off. The included mounting bracket will give you multiple options for placement on your vehicle.
I have included a diagram below so you can see the dimensions of this light and the mounting bracket. view full answer...
I went out into our warehouse to measure the thickness of the steel on the Rampage Off-Road Light Mounting Brackets # RA7608 and found it to be .138 of an inch.
These don't have a weight rating, but I can assure you that if you install and use them properly they will be plenty strong. view full answer...
I went ahead and spoke with Hopkins about the Blazer Off-Road Lighting Remote Control Kit # BL43VR and they informed me that the wire leads are 24" long and they do have ring terminals at the ends. view full answer...
The overall length of the Westin Off-Road Light Mounting Bar # 37-02580 is slightly less than the opening in the lower part of the bumper on a 2009 to 2015 Ram 1500. That opening is approximately 42 inches. The exact measurement of the bar was not available. I have included a picture showing the silver version mounted on a truck view full answer...
I do have an solution for you to use off-road lights on your 2016 Chevy Silverado 500, however when I contacted Aries they were unable to tell me the length of the harness that comes with the Aries LED Work Lights # AA1501250 and there are none currently available to me that I would be able to go and measure.
There are a pair of outstanding alternatives, the Vision X Optimus Single Prime Pod Light Kit # XIL-OP110KIT which have a narrow 10-degree spot beam, or the Vision X Optimus Single... view full answer...
I reached out to my contact at MaxxTow and the MaxxTow Off-Road Light Bar - LED - 300 Watts - Mixed Beam - 2 Row - 54-1/2" Long # MT80636 has 14 gauge wire that runs the power from the LED Bar to the relay and from the relay to the battery. I've attached a video to assist with this wiring connection. view full answer...
We have confirmed with the manufacturer that the Westin LED Off-Road Rock Light Kit for Jeeps # 09-80015 does work with 24 volt systems like you have. It works with 10 to 30 volts so 24 volts is for sure no problem at all. view full answer...
We went ahead and pulled the Optronics LED Off-Road Light Bar # UCL21CB from the warehouse, and it measures 15-1/8 inches between the mounting holes on the brackets. view full answer...
With an unloaded ride on your 2006 Toyota Sequoia, there will be approximately 1 inch of space between the axle and the bottom of the SumoSprings Solo Custom Helper Springs # SS68DR.
These are a light capacity helper spring, and if you are off-road without a load in the back, you will feel them engage, but it won't be extremely jarring. With normal driving, however, short of going over a speed bump or pothole or really bad roads, there won't be an issue of these springs affecting your... view full answer...
Unless you go with an incadecent or halogen light like the Optronics Utility Work Light item # TL46TS, they're all going to be pretty similar to the Optronics LED Off-Road Light Bar item # UCL23CB you referenced. This one has 15,500 lumens and is one of our most popular accessory lights. For the price you can't beat it and it comes with its own mounting hardware. If you find the light is too bright you can always add some tinting film over the lens to soften the brightness.
The LED Work... view full answer...
The Timbren Active Off-Road Bumpstops - Rear Suspension - 6,000 lbs # TABSTORSEQ are not designed for your 2016 Jeep Wrangler Unlimited. You will instead want the Timbren Active Off-Road Bumpstops - Rear Suspension - 2,400 lbs # TABSJRJK which are a confirmed fit for your vehicle. They measure 3-5/8 inches tall as you can see in the attached photo. view full answer...
The CIPA EVO Formance Spectras 9006 Halogen Headlight Bulbs # CM93423 have an 800 hour bulb life. They are for off-road use only due to the 1,300 lumens and 8,000 K color temperature they provide. I've added a link to an install video of these lights for you to take a look at. view full answer...
I checked with my contact at Pilot Automotive for the length of the wiring included on their Brake and Tail Light Trailer Hitch Receiver Cover # CR-007. My contact advised that the length of the wiring itself is approximately 14-inches.
If this is not long enough for your installation, we offer 4-pole extensions such as 12-inch # HM48145. view full answer...
We do have some options similar to the Optronics Halogen Utility Light # QH16CTS but a little smaller:
- Vision X Utility Market Floodlight # XIL-UF32 (456 lumens and measuring 3-1/2" long x 1-7/8" tall x 7/8" deep)
- SteelHead LED Work Light # TN49RR (750 lumens and measuring 3" long x 2" wide x 2" deep)
These have plastic lens but they do fit the criteria you're looking for when it comes to size. The Vision X looks a little more clean while the SteelHead has more of a classic, "off-road"... view full answer...
The InfiniteRule Lock for Gen-Right Off-Road and DV8 Off-Road Tire Carrier - Stainless Steel # 34061069-D shear strength is a maximum of 15,000-lbs that has been deemed as safe per the manufacturer's testing. The double shear strength according to InfiniteRule is going to be 27,000-lbs based off their testing. view full answer...
The Superwinch Tiger Shark Off-Road Winch # W85NF that you referenced does not require installing an additional fuse as it has one built into it. view full answer...
The Blue Ox Aftermarket Off-Road Bumper Adapter # BX88357 has a maximum rating of 10,000lbs. You would also want to check with the bumper manufacturer and see what their weight rating for Dinghy towing would be. So they will not be strong enough for what you want to do. There are currently no off road bumper adapters that are rated for over 10,000 lbs. And with checking with the baseplate manufactures the vehicle specific mounts are not rated for anything over the 2020 Jeep Gladiators GVWR.... view full answer...
I was able to have our warehouse measure the mounting plate for the Ark Extreme Off-Road Swing-Up Trailer Jack # ORJW350D you were looking at and included a diagram showing its dimensions.
The Ark # ORJW350D mounting bracket measure 7-1/2" tall x 5-1/2" wide. The vertical holes are 3/4" apart and the horizontal holes are 1" apart.
I included a video of the Ark Extreme Off-Road Swing-Up Trailer Jack # ORJW350D for you to take a look at. view full answer...
The distance between the opening of the Adapter for Off Road Bumpers part # BX88296 that you referenced is 1 inch. Check out the picture I attached to see this dimension and a few others as well. view full answer...