The etrailer.com J-Style Kayak Carrier # e98878 is designed to fit on a variety of crossbar styles, including most OEM crossbars. As long as your bars are smaller than 4" wide and between 7/8"-2" thick, the etrailer.com J-Style Kayak Carrier will work on your bars. If you measure your crossbars and they're not within those measurements, let me know and I will work to find you an alternative solution. view full answer...
All hitches that are made for the 2007 Toyota Sienna LE are designed to sit just below the rear bumper and are all close enough in ground clearance that it would not make a noticeable difference which one you picked. On the hitches we have installed we have found that from the ground to the top of the receiver opening is approximately 11 inches.
If you look at the picture to the right you can see a Draw-Tite Trailer Hitch for the Toyota Sienna, 2007, part # 75237 and the Curt # 13105 from... view full answer...
I went out to the warehouse and examined the Replacement Sidewind Handle and Gear Kit, # BD500256. The gears are identical. Each gear has a 0.5 inch inside diameter hole through it. The outside diameter is 1.1 inches. Each has two slots (a plus sign shape) on the bottom. view full answer...
The outside diameter of the Jacketed 6 Wire, item # DW04906-1, trailer cable is 1/2 inch. 14 gauge wire could be used for the brake and 12 volt power wires as long as the amperage requirement is not too high. The temperature coating on the wires in the 6 wire cable is good to 176 degrees Fahrenheit.
If your trailer is a single axle trailer with only two small brake assemblies, 14 gauge wire will be sufficient. We normally err on the side of caution and use larger wire for trailer brakes... view full answer...
The Replacement Hitch Tite Anti-Rattle Hitch Pin for Saris Bike Racks part # SA3021 uses a 1/2"-13 bolt. I am not sure what you mean by pin diameter as the above is a bolt, not a pin but if this was not the information you were looking for please just let me know. view full answer...
The tallest gooseneck ball for your 2018 Ram 2500 with the factory prep package is the B&W Ball and Safety Chain Kit for Ram Underbed Gooseneck Trailer Hitch # BWGNXA2062; you can see the difference in height between this and the Curt Ball and Safety Chain Loops Kit for Ram Underbed Gooseneck Hitch # C60618.
You will need more than 5 inches and if the height of the B&W does not allow you to tow with the proper clearance, or tow level, I strongly recommend switching to a 5th wheel hitch,... view full answer...
The B&W Companion 5th Wheel Trailer Hitch w/ Slider # BWRVK3400-5W weighs about 282 lbs while the Custom Underbed Installation Kit # BWGNRK1116-5W for your 2019 Ford F-250 Super Duty weighs in at about 143 lbs. I reached out to my contact at B&W who confirmed this so you will be adding about 425 lbs to your pickup.
Since you don't have the factory towing system installed I recommend adding the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness with 7-Pole Plug # 41157 as well.... view full answer...
You are correct that a level trailer will be less likely to sway and keeping your hitched trailer level will enable a weight distribution (WD) system to function at its best. It is perfectly okay for a hitch ball to be an inch or so higher than the coupler on the level trailer since a little bit of normal squat will even things out but if your trailer is tipped up at the tongue when it is hitched to your F-150 you'll want to select a different shank for your WD hitch that will allow the... view full answer...
The Taylor Made Bimini Top External Eye # 36911729 has a tab that measures 1-1/4-inch long x 1-inch wide x 1/4-inch thick and the hole diameter is 1/4-inch. I confirmed these dimensions with my contact at Taylor Made. view full answer...
I reached out to the manufacturer, Buyers Products, who told me the Buyers Products Safety Chain Clip - 5/8" Diameter # 337SC58B does not have a weight rating because it is a weld-on application, meaning it will only be as strong as the welds.
I have added a link to a video review of this clip for you to take a look at. view full answer...
The B&W Companion 5th Wheel Hitch # BWRVK3500 that you referenced has a total weight of 205 pounds. Keep in mind that the Companion is designed so that it can easily and quickly be broken down into 2 manageable components (the base and the head) when it's time to install or remove the hitch.
The head by itself weighs 73 pounds and the base by itself weighs 132 pounds. view full answer...
The base of the Replacement Dual Handle Faucet for D&W Inc Spray-Away Unit part # PF213790 is going to be 5-1/2" at its widest point. The hose that you will need to use with this unit is the Replacement Hose for D&W Inc Self-Storing Spray-Away Units part # PF267003. view full answer...
The online owner's manual for the 2010 Dodge Journey indicates (page 367) that the 2.4L version can tow up to 1000-lbs and this includes up to 5 persons and luggage. It also states that the most the vehicle and trailer together can weigh (the GCWR or gross combined weight rating) is 6000-lbs. Since the curb weight of the vehicle is a bit under 4000-lbs this suggests the car could tow close to 2000-lbs. This is shy of the 2600-lbs but not by a whole lot.
I cannot recommend you do anything... view full answer...
I went out to the warehouse and found that the outer diameter of the Curt Combo Bar # C49360 measures 2-1/2" x 2-1/2" so technically it should fit your 2-1/2" receiver. However, this part was designed to be welded and act as a hitch receiver so instead you will want to use the Curt Hitch Extension and Reducer # C45048 which gives you up to a 34" extension and was designed to be used this way. view full answer...
Yes, the wheel studs on the Dexter 8 on 6-1/2 Hub-and-Drum Assembly part # 8-393-6UC3-A will be long enough for most aluminum trailer wheels. The studs that are used on this hub are 5/8"-18 x 2-1/2". Therefore, they are 2-1/2" long. view full answer...
The dimensions of the rectangular metal nut part on the Yakima HD Bar SL Adapter 4-piece kit # Y03541 (their part 8003541) and the single piece part # 8880637 are shown in the linked image. The metal nut measures 1-1/8-inch x 3/4-inch. The overall height of the nut from the top to the wider base part is 3/4-inch. view full answer...
The Rapid Hitch Adjustable Locking Ball Mount # AM3400 has a total weight (with the hitch ball attachment) of just about 19 pounds. The shank by itself without the hitch balls is only 6 pounds.
I have attached a short video review on this product that you can check out as well. view full answer...
Basically nothing happens or has to happen if the batteries connected in the TorkLift PowerArmor Solar Locking Battery Box # TLA7710RS also end up connected to a charger. The solar panel would not get damaged and the batteries would not get overcharged. view full answer...