I confirmed with my tech at Swagman that the distance between the center of the pinhole to the outside edge of the furthest wheel hoop is 20.5 inches on the Traveler XC2 # S64663. I went ahead and attached a picture of this measurement to provide you with perspective. view full answer...
The overall dimensions of the Valterra Frame Assembly and Glass # A77051 are 15-3/4" wide x 24-3/4" tall. Just the frame is part # A77008 and those are the dimensions for just that. view full answer...
The Stromberg Carlson RV Exterior Ladder part # LA-401 measure 99-1/2" tall when measuring from the top of the handle to the bottom of the bracket which gets attached to the trailer. I have attached a photo of this measurement for you as well. view full answer...
The TrailerLegs Tire Saver Stands - Tandem Axle # 326-TRLLG-4 have overall dimensions of 15" long x 8" wide x 19" tall. In order for the rubber to grip and allow lift your axles will need to be a minimum of 11-1/2 inches off the ground. The manufacturer recommends using some wheel blocks like # A10-0918 to increase the height of your axle from the ground if needed to assist in making this system work ideally if your axle height is less than the 11-1/2 inches. view full answer...
I have never had a RV manufacturer tell me a weight rating for their bumper. They usually say its enough for the spare tire or a BBQ grill that they have mounted on to it.
I always recommend the Stromberg Carlson Bike Bunk Trailer-Mounted Bike Rack Carrier for A-Frame Trailers # CC-275. It will put your bikes where they are safer in front of the trailer. The rear is subject to a lot of hash bouncing and they become out of sight out of mind so you kind of forget they are back there. I... view full answer...
The best solution to keeping your toy hauler level over the winter months is to use the Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer item # UF19-950500. This stabilizer tripod has height adjustments from 31" to 54", 5,000 lbs tongue weight capacity, and large footplates to help prevent your trailer from sinking or tilting. This will take a lot of the weight off of your electric stabilizers and keep your 5th wheel level while in storage.
The Ultra-Fab item # UF19-950500 has height... view full answer...
No, you are absolutely correct. The Classic Accessories RV Tire Covers item # CA80087 will need to be removed before you drive down the highway. That's a ridiculous product description and I'll message someone about getting it changed.
The Classic Accessories RV Tire Covers item # CA80087 are sold in pairs and fit tire diameters from 37" to 41". These gray covers are water resistant and have a three year warranty. view full answer...
The load and speed ratings of the ST225/75R15 trailer tires your 2017 Dutchman Aspen travel trailer are maximum capacities for the tires themselves. The 75-mph maximum speed of an L-rated tire does not indicate a recommendation to tow a trailer at that speed.
Safe towing speeds naturally vary based on the nature of the road (dead-straight flat interstate versus winding two-lane back roads), the weather conditions and the total weight of the truck and trailer as a combined system. Also,... view full answer...
I reached out to my contact at Hidden Hitch and the Hidden Hitch Trailer Hitch # 89013 you have fits the 1984-1995 Jeep Cherokee XJ, and the 1984-1990 Jeep Wagoneer XJ.
If you are needing replacement hardware for the hitch we have the # RHK. You will just need to select Hidden Hitch from the drop down menu and then enter 89013 in the hitch item number box.
I included a video of the # RHK for you to take a look at. view full answer...
Without knowing your particular setup on your Dutchmen Travel Trailer, the best way to determine your inner bearings is to pull the remove the hubs and find the number on the bearing itself. You can also measure the spindles where the bearing sits. In many cases, there can also be an axle tag on your axle beam that tells you information about the spindles you have.
I went ahead and attached a chart that shows the measurements you need to help determine your bearings. The best way to get... view full answer...
A gearbox like the Lippert # LC276602 won't have a weight capacity since it's not a weight bearing part; this unit is typically used with landing gear that have capacities of up to 10,000-lbs. Landing gear systems are designed to support the pin weight of your trailer, so I don't see a situation where you'd have more than even 5,000-lbs on them.
As long as you've got Venture landing gear and motors on your Dutchman 5th wheel then this gearbox will work for you. view full answer...
Yes, the Sew-In RV Slide Tape # 37281365 uses 3/8" snap clips. The clip measures 1/2" by 1/2" outside edge to outside edge. The clip measures 1/4" in between the teeth at the top of the clip and 3/8" inside the clip under the teeth. I have included a picture demonstrating this as well. view full answer...
We do have the Solera XL 30" Projection Window Awning in solid black as part # LC49FR on our site.
The 42" width is just the fabric and when I reached out to my contact at Lippert they said that the mounting hardware should add about 1-1/2" to either side of the awning so you're looking at a total width of about 45".
Please note that the support arms are sold separately as part # LCV000334764 so you'll want to pick those up while you're at it if you don't already have them. view full answer...
The Tork Lift Power Armor DH Locking Battery and Storage Box # TLA7712R has a weight of approximately 14.5 lbs and a shipping weight of 20 lbs.
The frame is durable and powder coated, preventing it from rusting and corroding. It comes with hold-down straps, locking lid, access hole for wiring, and hardware.
I have attached a video reviewing this product. view full answer...
From the top of the bracket of the MORryde X-Factor Dropdown Crossmember # MR84AR down to the top of the crossmember measures 4 inches. view full answer...
The switch panel dimensions the switch # BL0108-00 is designed to fit measures 3/4 inch by 1/2 inch like the panel you have. This is a standard switch with two spade connectors so it should fit and work well for you. view full answer...
Most of the old Atwood propane or carbon monoxide detectors have been discontinued and sold out so options are pretty limited. Since I don't know the model of your detector or size of your cutout hole I can't say for certain that the RV Propane Gas Detector # RS64FR will cover the existing hole, but I can say that it comes with two trim pieces with the following dimensions to help cover the old cutout:
The long plate measures 7-1/4" wide, 3-3/8" tall and hole to hole measurements of 6"... view full answer...
Since your axles are already below your leaf springs the only option is the Correct Track Trailer Alignment and Lift Kit item # RR23QX. This kit mounts to your spring hangers and moves the attachment point down 1-1/4" or 2-1/4". This adds extra brackets to the hangers but again it is the only aftermarket option.
Heavier springs won't do anything to help your ride height unless your springs are old and worn out which still wouldn't be anywhere close to 1-1/2" - 2". Lift blocks or at least... view full answer...
Yes, it will. The Lippert High-Speed Power Stabilizer Jack item # LC298707 is the replacement for your LCI 113407.
I have linked an installation video below so you can see how to get it set up. view full answer...
There are three things that typically cause heat-related tire failure: incorrect inflation, excessive speed and overloading the tire beyond its weight rating. Since you maintain your Westlake ST235/80R16 trailer tires at their full recommended 80-psi pressure (the right thing to do!) and operate them below their maximum rated speed that leaves the weight load on the tire as the potential smoking gun. Apart from these three causes the most likely reason for such a massive failure is a bit... view full answer...
Go To Results