I looked up the owners manual for your truck and your maximum trailer weight capacity is 9,200 lbs and your GCWR is 15,000 lbs.
Timbrens # TGMRCK15S are designed to help support the rear of the vehicle when towing a trailer. They essentially stop the vehicle from sagging too far in the rear. I recommend getting a weight distribution hitch that pairs well with the travel trailer that you decide on. We have many to choose from that will help with sagging and sway control.
I have provided... view full answer...
Thanks for the measurements and additional information! To determine which MORryde Equalizer you need you'll want to measure the distance at the bottom of your current equalizers from the center to the center of the bolt holes.
The MORryde item # MR87ZR measures 6-1/2" and is for 33" wheelbases.
The MORryde item # MR27ZR measures 8" and is for 35" wheelbases.
I have linked a couple of diagrams below.
To replace your 2-1/4" shackles, I recommend the MORryde Suspension Upgrade Kit item... view full answer...
The ideal situation for using a weight distribution hitch is that the towing system's total tongue weight (TW) falls in the middle of the hitch's operating range. Total TW consists of the fully loaded trailer's actual measured TW (measure with scale # e99044) plus the weight of cargo in the tow vehicle that sits behind the rear axle. For the best towing performance this combined figure should fall near the middle of the system's range. Please refer to the article and video for more details.
The... view full answer...
The diameter of your 205/75B14 tire is 26.1", and has a width of 8.1".
If you are needing a replacement tire I recommend the # AM1ST86 if you only want to replace one tire, or the # AM10235 if you are ok with replacing both tires.
The reason for this is the # AM1ST86 is a bias ply tire like your current tire, which you can tell by the B in the size between 75 and 14, where the # AM10235 is a radial tire. Radial and bias ply tires have a different sidewall construction making them not... view full answer...
Thanks for all the information. I wasn't able to identify what suspension system you have on your Holiday Rambler. A couple of people thought it might be a custom job. To replace it you will want to measure the distance between your two axles. If it is 33" you will want the MORryde Rubber Equalizers item # MR87ZR. If it is 35" you'll want the MORryde Shock Absorbing Suspension Equalizers item # MR27ZR.
The Road Armor Shock Absorbing Equalizer Kit item # LC696740 isn't going to work with... view full answer...
Lippert is a little funny when it comes to their 4,400 lbs axles. They don't have a true standard 4,400 lbs axle. Instead, they have some that use the same inner and outer bearings as a 3,500 lb axle (# L68149 and # L44649) and some that match the Dexter 4,400 lbs axles which use inner and outer bearings # L68149 and # LM67048.
Anytime I come across one of these axles I always ask to pull the outer bearing out and find the number stamped in the bearing.
The other option is to pull the... view full answer...
The inside dimensions of the MORryde RV Cargo Sliding Tray # MR47FR is 58-1/4" long x 22-7/8" wide.
Additionally, this unit has overall dimensions of 60" long x 26" wide x 6-5/8" tall, has a maximum weight capacity of 800-lbs, and will work with RV cargo compartments that are at least 60" deep.
Attached is a product review video for you to check out if you haven't already. view full answer...
There is a folding double step that has the same 24-1/4 inch wide x 8-1/4 inch dimensions as the Lippert Manual Pull-Out Step for RVs - Single # LC432678; the step you are looking for is the following:
- Lippert Manual Pull-Out Step for RVs - Double # LC432682
I have added a link below to a video review for you to check out as well if you'd like to take a look. view full answer...
The rails that come with the Lippert Replacement Dual Rack Standard Repair Kit for RV In-Wall Slide-Out
Item # LC84FR are both 42-3/4" long. view full answer...
Go To Results