K Source Universal Clip-On Towing Mirror, part # KS3890 is a universal fit towing mirror so as long as you have a lip on the edge of your mirrors, these will work great for you. These mirrors are sold in a pair and will attach to either the driver or the passenger side mirrors. These mirrors measure 7-3/4 inches tall by 5-1/8 inches wide. I have attached a link to a product review video for you. view full answer...
The Furrion Chill Replacement RV Air Conditioner for Furrion Setup - 15,000 Btu # FR58PR will only fit roofs 3-1/2" to 6" thick so you will need to increase the thickness of your roof at least another 1-1/2".
If you don't already have a a Furrion setup in your trailer you'll want the # FR92PR which will also come with the air distribution box (which also has controls on it) or the # FR55PV which will come with the air distribution box and a wall thermostat. view full answer...
Good news, transmission coolers are not vehicle specific so you will be able to use one on your 1990 Chevy motor home. The cooler you have referenced, the Derale 8000 Plate-Fin Cooler, # D13503, is listed as a recommended cooler for the 5.7 liter Chevy motors for the 1990 model year.
I have included some links to FAQ articles and a video for you that explains installation. view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13016 is a fit for your 1995 Coachman Class B camper van. It is a fairly easy installation bolting up in about an hour with the possibility of holes needing to be enlarged. I've linked the installation instructions to assist.
If you will be towing with this hitch receiver, I recommend also using the Curt Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C55338 for your wiring harness. Then you can use the Curt... view full answer...
Since the B-W 3230 Converter Charger is also you DC distribution panel you have two choices when it comes to replacement.
Option 1: You replace both this unit as well as your AC distribution panel with a power center like the Progressive Dynamics 4100 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel - 35 Amp # PD4135K. This has the Ac and DC distribution panel and converter charger all in one package to handle your motorhome's electrical components.
Option 2: You replace... view full answer...
I went out and tested one of our 30 Amp Plugs on the Valterra Electrical Cable Hatch # A10-2137VP and found that while the plug itself could probably be pushed through with a little muscle, the determining factor there was the plug's grip which did not allow the plug to pass through the back of the hatch.
Since I don't know what kind of 30 Amp plug you have or how big the grip is on it (if it has one), I can tell you that the back of the hatch measures 3-1/2 inches in diameter and that... view full answer...
Definitely not as that's for mid-2000s Silverado/Sierra trucks; the trailer hitch with the highest capacity for your 1985 Chevy G30 van is the Curt Trailer Hitch Receiver # C13016.
This has at 6,000 lb towing/600 lb tongue weight capacity that can reach up to 10,000 lbs towing/1,000 lbs tongue weight with the use of a weight distribution hitch. If you are indeed towing with the # C13016 and also need a 4-way wiring harness, the right fit is part # C58044. view full answer...
For your 1994 Chevy P30 step van you are going to want a multi-fit hitch as there are no custom fit hitches like the Hidden Hitch trailer hitch that you referenced that are confirmed to fit your van.
I would recommend the Curt Hitch part # 13703. This hitch can fit vehicle frames that are between 22 and 72 inches. As long as the width of your frame fits within that range this hitch would work well for you.
For ball mounts I recommend the etrailer Ball Mount Kit # 989900. It comes with... view full answer...
The Roadmaster Reflex Steering Stabilizer is no longer offered from Roadmaster but we do still have the brackets you would need to attach this to a 1989 Chevrolet 1500 Van Chassis, the Custom Mounting Brackets for Roadmaster Reflex Steering Stabilizer part # RM-RBK1. Therefore, all you would need to do is find the steering stabilizer whether that be new old stock or secondhand.
Unfortunately, we don't have a way to mix and match parts from other kits. view full answer...
I have a trailer hitch that is a confirmed fit for your 1993 Chevrolet G20 Van, but the Curt # 13028 will not fit on your Van.
Draw-Tite has a 2 inch Trailer Hitch, part # 41121, that is a confirmed fit for your Chevy Van as long as it doesn't have a step bumper. This hitch has a Gross Trailer Weight of 5,000 lbs and a Max Tongue Weight of 500 lbs.
If your Van does not have a wiring harness already installed you can use the Curt Wiring Harness, part # C55338. If you are needing to upgrade... view full answer...
Curt front-mount hitch # C31016 is specified to fit certain GMC and Chevrolet vans and RV cutaways but not until the 1996 model year. I show no custom-fit front-mount hitches for this vehicle, only rear-mount hitches from Draw-Tite, # 75121 and # 41121 for vans without the step bumper.
I also checked directly with Curt and Draw-Tite and neither shows any front hitch fits. My Curt contact suggested a universal-fit RV-type hitch as a possible work-around.
We do offer several adjustable/universal-fit... view full answer...
The best option for a vintage van usually the MaxxAir # MA00-335001 universal vent cover. I would still closely examine the hinge type.
Most likely we have what you are looking for but you will need to first determine what vent style you have on your trailer.
In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14".
To pick the correct cover, you will also... view full answer...
According to Curt, the manufacturer, the CurtWiring Harness, # C55338, will fit your 1995 Chevy Van, even if it has a step bumper. I have included a link to the installation details for you to view. view full answer...
There unfortunately isn't a custom-fit trailer hitch confirmed to fit your 1996 G30 Camper Van since it's been modified from the original Van base. You would instead need to install an adjustable-fit trailer hitch like the Draw-Tite # 41990-07 (7" drop) or # 41990-16 (16" drop). These hitches can fit a frame width of up to 44" and would need to be welded onto the frame. view full answer...
If the chrome mirrors on your 1993 Chevrolet Van have the black trim then I have another solution for you, but neither the Cipa # CM10000-2 or the Longview # LVT-1000 custom mirrors will fit.
Instead of custom mirrors you will need to use universal mirrors. One of the more popular towing mirror options is the K-Source Universal Dual Lens Towing Mirrors # KS3990 which have a clip-on application and come in a pair.
As long as your mirrors are 4-1/2" to 11-1/2" tall then you are good to go! view full answer...
First, thanks for the kind words, they are genuinely appreciated. And as far as questions go, asking about a front hitch on your 1995 Chevy G30 is not crazy at all, it is perfectly reasonable to wonder! But as you may have suspected, there is not a front hitch, just a rear hitch. I bring that up as you said you want to do a rear one, so when that time comes the correct part is the Curt Trailer Hitch Receiver # C13016.
Then if you also wanted a wiring harness you'd need the T-Connector... view full answer...
For your 1989 Chevy Van Cutaway, I recommend the Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2" # 41121. If this will not fit with the waste water tank, then I recommend the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703. If these brackets won't fit, you will need to make a completely custom hitch made by a professional welder. If this is the case, they often like beginning with the Combo Bar 12" with 2" Trailer Hitch Receiver... view full answer...
The GloLight LED Trailer Tail Light # STL178RB will not work with the Snap-on Reflector Ring for STL78RB Series LED Lights # A78RXB as it will not fit the light. If you wanted to use that reflector ring you would need the Optronics LED Trailer Tail Light # STL78RB.
This is similar to the GloLight but has a lip around the edge that allows it to accept the Reflector Ring.
You can use these lights for your trailer as long as they have the side marker lights. I have added a link to a help... view full answer...
The Curt Trailer Hitch Receiver part # C13016 is only a confirmed fit for a 1978 - 1996 Chevrolet Van which excludes conversion models. The reason for this is because the conversion van models do not have the mounting hole for the bumper which is the front facing hole on the Curt Trailer Hitch Receiver closest to the receiver tube opening. I spoke with Curt and all they were willing to release is the distance between the two holes left to right which is 40.873".
I recommend the Adjustable... view full answer...
The Duplex Outlet Cover # 37247505 measures 4-3/4" long, 2-7/8" tall, and is 15/16 of an inch at the thickest point. If these measurements match what you need, then yes it will work for you. There isn't really a fit or not fit guide for outlets/outlet covers, they're usually universal. view full answer...
Go To Results