You will need to be able to access the three bolts on the inside of the tailgate that secure the handle to the tailgate. If you have a slide-in bedliner you will need to temporarily remove it to do this.
If its a spray-on liner and you can access the bolts fine then you would obviously not need to remove the liner. view full answer...
I spoke with my contact at Tekonsha and he stated that they have not tested the brake controller wiring harness on a 2006 Mitsubishi Raider. So, while it is possible that it will fit if the truck has a factory tow package that includes a 7-Way trailer connector, since it has not been tested I cannot say for sure if it will or not.
Instead, you can hardwire the controller. If the truck does not have a trailer connector, you will need to first install # 118323. I have included a link to... view full answer...
The taillight wiring colors for your truck could be any color, manufacturers change wiring colors for many different reasons and often within the same model year. To determine the correct wires to use on your vehicle you will need to use a circuit tester, item # PTW2993 if needed, and test the wires behind the vehicle tail lights.
On the driver's side you should be able to find a wire that carries the left turn/brake signal and a wire that carries the running light circuit. Connect the... view full answer...
Yes, the Weather Tech Easy-On Stone and Bug Shield Deflector # WT50150 that you referenced is sturdy enough and mounts sturdy enough to survive going through a carwash. view full answer...
For a 4-way wiring harness recommendation for your 2007 Mitsubishi Raider you would want the Curt T-Connector Vehicle Wiring Harness # 55323. I attached an install video for you to check out as well.
Now to convert this to a 7-way you will need the part # 37185. view full answer...
For your 2006 Mitsubishi Raider, the Derale Series 9000 Plate-Fin Transmission Cooler Kit w/ NPT Inlets - Class I -Extra Efficient # D13611 is a small but strong transmission cooler. It requires no extra fittings for installation.
For a better transmission cooler, I recommend the Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class III - Efficient # D13503. This cooler is designed for Mitsubishi Raiders with late-model, electronic overdrive transmissions. This... view full answer...
If you have a rear driveshaft disconnect on your 2008 Mitsubishi Raider 2WD it can be flat towed with all 4 wheels on the ground. You could use the base plate kit part # 52276-1 that you referenced.
In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. The most popular compatible tow bar is the Falcon All Terain, # RM-522. This has non-binding arms which makes the setup very easy to connect/disconnect.
For... view full answer...
I have found several toolboxes that will fit your 2006 Mitsubishi Raider, however, the DeeZee Toolbox # DZ8748HDS is not one of them that will sit below your rails.
The 3 series of toolboxes that should fit below your rails are DeeZee # DZ8537, # DZ8546, and # DZ9560, however, you will need to measure the bed of your truck to pick the right toolbox for you.
The DZ8537 series is 37-1/8 inches long, 19 inches wide and 15-9/10 inches high. There is also a black version, # DZ8537B. I have... view full answer...
The trailer wiring harness part # 118323 that you referenced is the correct harness for your 2007 Mitsubishi Raider. It does not have a converter on the harness though so that indicates that it picks up a stoplight circuit directly from the harness and the vehicle does not use variable voltage for stoplight activation. That style of taillight circuit is referred to as multi-plexed. view full answer...
According to Hopkins installation manual, the E2 error indicates that there is a blue wire short somewhere in along the trailer wiring or a possible defective magnet in the brake assemblies.
First, you will need to check the blue wiring from the brake controller to the the trailer electric brakes. Check your electrical connection between the your vehicle and your trailer. The plug might not be making a secure connecting, causing an intermediate signal.
There could be an electrical short... view full answer...
Go To Results