I spoke with my contact at SeaSucker and they told me that typically the cups last 5-8 years depending on how often they are used, weather, etc. view full answer...
I will start by confirming that the Curt # C11529 is a fit for your 2022 Hyundai Kona and it will indeed have a 1-1/4" receiver opening so there will be no issue getting your bike rack installed in it. I can also say that we have not needed to do any drilling or trimming to get this hitch installed and I included an install video we did on a 2020 Kona for you to check out. You will need to lower the exhaust, which is not difficult, and there is a small panel that needs to be removed while... view full answer...
I sure can!
I linked the instructions for installing the Draw-Tite Trailer Hitch Receiver # DT52GR on your 2021 Hyundai Kona. You will find the link below the answer, you will just have to scroll down a little bit to see them. view full answer...
The Thule EasyFold XT Bike Rack for 2 Electric Bikes, # TH903202 folds upright from the sides. See the attached images. It will also tilt out from the vehicle to assist with easier access to the trunk or SUV cargo area.
Please note the linked product review video showing operation of the Thule EasyFold XT Bike Rack. view full answer...
For your 2019 Hyundai Kona, I recommend using the Curt Trailer Hitch Receiver part # C11529. The reason I recommend using this trailer hitch is because it will come with a set of step by step instructions with photos that will break down every part of the process to install the hitch on your Kona. I have attached these instructions for you as well so you can get an idea of what all is involved but we do not have a video as of February 2019. The process is rated at "easy" on the difficulty... view full answer...
The Draw-Tite # DT52GR trailer hitch for your 2022 Hyundai Kona is a direct bolt on application that will require no drilling to get installed. The underbody panel(s) and/or fascia must be temporarily loosened or removed and then trimming may be needed to reattach the underbody panel or the fascia. The exhaust must also be temporarily lowered for installation. view full answer...
Typically when people remove a trailer hitch receiver that uses bolts that need to be installed using a fishwire like those found on the Curt Trailer Hitch Receiver # C11529 for your 2020 Hyundai Kona, they carefully remove the hitch and reinstall the nut to keep from having to completely remove the hardware.
If you would rather completely remove the hardware you can use a flexible magnet to get the bolt and washer out of the frame.
I included a video of the # C11529 being installed on... view full answer...
Yes. The Draw-Tite # DT52GR is a confirmed fit on the 2021 Hyundai Kona EV. I have linked the installation instructions for the Draw-Tite # DT52GR for you to have a look at, but it looks like the passenger side dust panel will need to be removed for installation of this hitch. It's not anything that's going to affect the performance or operation of the vehicle. view full answer...
The Curt Trailer Hitch Receiver part # C11529 which fits the 2020 Hyundai Kona will not require any permanent modifications to the vehicle so you can revert the vehicle completely back to stock once your lease ends without having to worry about any charges for damage. The Curt hitch is a 100% bolt-on fit with no cutting or drilling required. I recommend the Curt hitch as they just tend to fit a bit better in my experience but either option is a good choice that will work well.
If you don't... view full answer...
I am happy to verify for you that no drilling, fascia trimming, or cutting is required during the installation of the trailer hitch receivers that fit your 2022 Hyundai Kona:
- Curt Trailer Hitch Receiver # C11529 view full answer...
No drilling is required to install the Curt Trailer Hitch Receiver # C87DR on your 2022 Hyundai Kona, but you will need to trim some of the fascia for this to fit properly. All of this is outlined in the installation instructions for you to check out! view full answer...
The wiring harness that needs to get moved to install the Curt hitch part # C11529 is attached to the bottom of the frame through a small hole. I lightened up the picture that's in the install instructions so that you can actually see it. Basically it just pulls straight out like you mentioned.
There are three push pins that need to be removed to remove the panel you mentioned as well as a bolt. view full answer...