Expert Answers about Ford Bronco
- Are Only Square Spacers Available as Replacement Hardware for Draw-Tite Hitch?
- The square spacers would not be available alone, the entire kit hardware kit for your Draw-Tite 40050 would be needed.
Simply go to # RHK and type 40050 in the "Hitch Item Number" box and then select Draw-Tite from the "Manufacturer" drop-down.
view full answer... - Replacement Caps For Blue OX Base Plate On 2023 Ford Bronco
- Yes, we have the Replacement Caps # BLU96XR. These will fit into the hole on the Base Plate # BLU23XR when you are not flat towing your Bronco.
view full answer... - Additional Mounting Hardware for the Erickson Removable Motorcycle Wheel Chock
- We do have mounting hardware available for the Erickson Removable Motorcycle Wheel Chock - 6" Wide Tires # EM07506. What you are looking for is the Replacement Mounting Plates for Erickson Removable Motorcycle Wheel Chock # EM56ZV. You would just need to pick up some 1/4" bolts similar to the ones that come with the original kit to finish the installation.
view full answer... - 2024 Ford Bronco Roof Rack and Cargo Box Recommendations
- To get a robust and factory looking rack on your 2024 Ford Bronco I recommend the Yakima TimberLine FX Roof Rack for Raised Side Rails # Y48UV. This clamps to the raised rails but has the crossbars ending in the legs so you get that sleek OEM look but without the thin OEM crossbars that don't always feel sturdy.
For a cargo box I recommend checking out the Yakima SkyBox NX 18 # Y45AV because it has a Black Carbonite finish that matches matte black finishes on vehicles, plus it has more...
view full answer... - Replacement Clevis Pins For The Curt Base Plate C59JR
- Yes you can absolutely use a different pin as long as it has the correct diameter. We carry pins here that will be perfectly acceptable to use, but we do not have a direct replacement for the pins that came with your Curt base plate # C59JR. Curt does make a generic clevis pin. We have;
# C45805 for a 1/2" diameter pin.
# C45804 for a 5/8" diameter pin.
# C45803 for a 1" diameter pin.
view full answer... - Replacement Tower For Yakima Roof Rack With Timberline Towers on 2022 Ford Bronco
- It sounds like you are looking for a single Yakima TimberLine Tower # 8880628 for a roof rack on your 2022 Ford Bronco. If this is what you are needing please let me know exactly what roof rack system you have so I can verify if this is the correct tower. Otherwise please give me some more information on exactly what part you are needing.
view full answer... - Replacement Covers for 2022 Ford Bronco Blue Ox Base Plate Kit When Pins Are Removed
- Yes! To cover the holes when the pins are removed from the Blue Ox Base Plate Kit # BLU23XR on your 2022 Ford Bronco you need the Replacement Cap # BLU96XR which comes with 2 of them. This will help to keep dirt and debris out during normal driving but you may want to remove them and clean are riding some trails as I'm not sure how "trail-proof" they are.
Unfortunately there aren't any D-Rings that can be used in place of the removeable pins. Since D-Rings are designed for recovery purposes...
view full answer... - Replacement Hub for 2009 Karavan WC-2200-84 Series Trailer
- According to Karavan, your current inner and outer bearing are the # L44649 and your current hubs have a 5 on 4-1/2 bolt pattern. There is no information on the axle capacity but based on the GVWR of 2,675 lbs for the trailer I would recommend the CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased # CE13315 as a replacement.
In addition to the hub, you will need to get a different seal since the # CE13315 uses a seal with a 1.50" inner diameter....
view full answer... - How Does the CIPA Replacement Mirror CM42221 Install on a 1996 Ford Bronco
- The mirror may look differently from what you currently have installed on your 1996 Ford Bronco, but the # CM42221 would install in the exact same place as your current mirror. The footprint for the mounting studs would be the exact same. You would just need to remove the interior trim piece that covers the install bolts from the inside of your vehicle so that you can loosen the nuts and remove the mirror. To reinstall the new mirror you would just need to reverse the process.
view full answer... - 1992 Ford Bronco Curt Hitch Replacement Hardware
- For replacement hardware you need the Kit # RHK. When you get to the page just choose Curt as the manufacturer and then input the correct hitch part number, like # C15300 for example, and you're good to go!
view full answer... - Replacement Bumper With Custom Fit Brackets for 1989 Ford Bronco XLT
- The # 76001 is not a direct fit for your 1989 Ford Bronco. Instead you will want the Westin Fey Surestep Rear Bumper with Custom Installation Kit - Chrome Plated Steel # 21002-95600 which is the same style bumper in the correct fit for your Bronco. We also have the similar Westin Fey Surestep Deluxe XLT Rear Bumper with Custom Installation Kit - Chrome Plated Steel # 21007-95600 which is a similar design also a custom fit.
view full answer...
Go To Results