Expert Answers about Chrysler 300
- Will Yakima EasyTop Universal Fit Roof Rack part # Y07418 Leak Water
- We had one customer come back and tell us that in a heavy rain the fabric straps of the Yakima EasyTop Universal Fit Roof Rack part # Y07418 did allow some water to drip into the interior of the vehicle. Unfortunately there's no way to avoid that unless you'd be willing to install a roof rack like the Rhino Rack part numbers # RRVA137B-2, # RRRLKVA, and # DK318 which is a much more secure rack for your 2013 Chrysler 300 and will not leak.
view full answer... - Hitch Mounted Bike Rack Carrier And Receiver For a 2019 Chrysler 300S E-Bike Weighing 70LBS
- For your 2019 Chrysler 300S you will need to check your specific vehicle to determine if your drivers side muffler can be removed. I was unable to find a direct answer from Chrysler as to if this was model year or trim specific. The Curt Trailer Hitch Receiver # C13093 does recommend removing the drivers side muffler to install it but like the other receivers if you have a welded on muffler you can remove the rear fascia to install the receiver.
We have added a new feature to our website...
view full answer... - Recommended Trailer Hitch to Carry Bike Rack and Cargo Carrier on 2006 Chrysler 300
- The Curt Class III - 2 inch trailer hitch # 13465 is a confirmed fit for your 2006 Chrysler 300. This hitch has a maximum tongue weight of 350 lbs. and would work well with a bike rack and a cargo carrier. This is a bolt-on installation with no welding required. I have attached a video of this hitch being installed on a 2006 Chrysler 300 for you to check out.
You should note that all non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps....
view full answer... - Will the Saris Bones fit my 2017 Chrysler 300S with Spoiler?
- I checks Saris's web site and they do confirm the fit for the Saris Bones 3 Bike Carrier part # SA801BL on your 2017 Chrysler 300S.
view full answer... - How to Determine Which Ball Mount Will Have Enough Rise for Curt Hitch on a 2005 Chrysler 300c
- The best way to determine which ball mount is right for your 2005 Chrysler 300c and your trailer is to take a few simple measurements.
Since you don't have the hitch we can see by the video of the Curt # 13465, I've attached, that the hitch receiver is going to be 10-1/4 inches from the ground. You will then want to take a similar measurement from the bottom of the coupler to the ground. Then compute the difference.
If the hitch height is greater than the trailer height, then
•hitch...
view full answer... - Fit of Thule TH78VR Gateway Pro 3-Bike Rack on 2021 Chrysler 300
- The Thule # TH78VR Gateway Pro 3 bike rack is a confirmed fit for the 2021 Chrysler 300. The rack can handle 3 bikes weighing up to 35 lbs each. If you have a women's bike with a step through frame or a bike with a sharply angled top frame tube like a hybrid bike, you'll want to use a frame adapter bar like part # SA3040. I'll link to product demonstration videos for the Gateway 3 bike rack and the frame adapter bar, so you can see how they work.
Anytime a bike rack is touching the painted...
view full answer... - Does Tekonsha Trailer Wiring Harness 118658 Fit 2019 Chrysler 300C
- I checked with Tekonsha and they list the trailer wiring harness part # 118658 as a confirmed fit for all models of the 2019 Chrysler 300 so that would also include your 300C.
view full answer... - Trailer Hitch that Fits 2007 Chrysler 300 SRT8
- Yes, the Draw Tite hitch part # 76145 that you referenced is a confirmed fit for your 2007 Chrysler 300 SRT8 with a 6.1 liter V8 and would work great as it fits all models of the 2007 300.
view full answer... - Is the Four Pin Brake Controller Connector Installed Under the Dash on All 2004 Ford Explorers
- The Hopkins Plug-in Simple Brake Wiring Adapter - Ford, item # HM47715, will only work on Ford Explorers that have the factory installed 7-Way connector at the rear of the vehicle. Since your vehicle has a 4-Way flat connector at the rear of the vehicle you will need to do some extra wiring to install a brake controller.
The easiest way to wire a brake controller on your Explorer is to use a brake controller installation kit, item # ETBC7. You will need to plug the connector into the...
view full answer... - Will DeeZee Universal-Fit, Brite-Tread Mud Flaps, # DZ1808 Fit a 2008 Chrysler 300 without Drilling
- The DeeZee Universal-Fit, Brite-Tread Mud Flaps, # DZ1808, are a universal fit item so fit guide information for specific vehicles is not available. You can measure your 2008 Chrysler 300 to see if they can fit. The flaps are 11 inches wide at the widest point and 19 inches tall at the tallest point.
If you determine that the mud flaps will fit, there is drilling required. Once you have aligned the flaps in the desired location, you will need to drill 3 holes through the flap and wheel...
view full answer... - How to Use Roof Top Tent with 2014 Chrysler 300
- I have a way for you to transport and use a roof top tent, like the Yakima SkyRise HD Tent # Y07436, with your 2014 Chrysler 300 but every roof top tent I've looked at says not to mount and use a tent on a roof rack that uses clips for the door jambs like what we see with this Yakima setup. The 165 lb weight rating is the dynamic rating so the static rating would be higher, but we need to look at a different solution since a clip-style roof rack shouldn't be used for this application.
As...
view full answer... - Correct Trailer Hitch for a 2013 Chrysler 300S
- The trailer hitch options for 2013 Chrysler 300 are all compatible with the S models. I recommend going with the larger 2" opening due to the higher capacity and abundance of hitched mounted accessories for this size. The Curt Trailer Hitch Receiver part # C13093 offers a bolt-on fit with no drilling required.
view full answer... - Fixed 2" Ball Mount w/ 10-3/4" Rise and 12" Drop
- Yes, we do carry multiple hitches, ball mounts, that are similar to the Convert-A-Ball Ball Mount for 2" Hitches item # AMSC12 you were looking at. The closest comparable product would be the Brophy Trailer Hitch Ball Mount 10" Drop, 7,500 lbs item # BM10. If you have some more specific requirements please email me back with them and I can make a better recommendation. I have linked our entire selection of fixed ball mounts below.
view full answer... - Recommended 4-Way Wiring Harness for a 2019 Chrysler 300
- Kayak trailers usually have a 4-way connector because they're not heavy enough to require brakes. To add a 4-way connector to your 2019 Chrysler 300 you will want the Curt T-Connector Vehicle Wiring Harness item # C56235. This wiring harness is custom fit and plugs into existing wiring behind your rear tail lights.
I have linked an installation video below that will show you how to set this harness up.
I have listed some other parts you will need to tow a trailer with your 2019 Chrysler...
view full answer... - Compatible Trailer Hitch Receiver For A 2019 Chrysler 300 Limited
- Yes, the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 76145 is a confirmed fit for your 2019 Chrysler 300 Limited. This hitch has an easy, bolt-on installation with no welding required. The complete hardware kit and installation instructions come included. I've also attached an installation video to walk you through this process step by step.
If your Chrysler 300 doesn't already have a 4-pole connector then I recommend the T-One Vehicle Wiring Harness with...
view full answer... - Will Curt 20x60 Folding, Aluminum Cargo Carrier, # C18100 Fit a 2008 Chrysler 300
- You will need to measure from the center of the hitch pin hole out to the distance required to clear the rear of the vehicle on your 2008 Chrysler 300. We have two videos that show this distance is 8 inches with a Class III trailer hitch installed but you will need to verify on your actual vehicle.
I went out to the warehouse and assembled a Curt 20x60 Folding, Aluminum Cargo Carrier, # C18100, to measure it. In the folded position, it measures 5 inches from the center of the hitch pin...
view full answer... - What is the Best Trailer Hitch and Wiring for a 2014 Chrysler 300 Base Model with 3.6 Liter Motor
- Yes, Curt trailer hitch # C13093 fits all models of the 2014 Chrysler 300 including the base models.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use...
view full answer...
Go To Results