Since you don't have an air distribution box to remove and check the wiring you'll need to unbolt the unit from the roof and determine how the rooftop unit connects to the controller. The Advent Air # ACDOM135B comes with a 6-pin connector to plug into the controller. If your Dometic system is hardwired then you can cut the connector off and hardwire it in, but you'll void your warranty and would still need to reach out to Dometic for a wiring diagram to match up the correct wires. If you... view full answer...
You will not have any problems fitting the Demco SBS Coach Air Kit for Air Force One Supplemental Braking System # SM99627 to your 2015 Newmar Ventana 3635 with the Freightliner chassis. I have included images from the instructions showing the air lines to connect to on your Freightliner chassis. view full answer...
The Sentry Deflector for Demco Tow Bars part # DM9523135 actually mounts to the base plates, not the tow bar. That said, if you have a Roadmaster Tow Bar then you likely have a Roadmaster Base Plate Kit and the Sentry Deflector for Demco Tow Bars will work if you use the Demco Sentry Deflector Adapter Kit for Roadmaster Base Plates part # DM9523027. view full answer...
For your 2022 Newmar Kountry Star 4037 Motorhome I recommend the Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional # 90195. There currently isn't a custom wiring harness so you will have to splice the wiring together to install this brake controller. The trailer wiring harness for your motorhome should be bound up together under the dash. Typically manufacturers will bundle the wires together and have a label hanging off them.
The wiring connections from the brake... view full answer...
The only option we have for a hitch for your school bus with a 34 inch frame is a weld on hitch:
- Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop # 15901
This is for frames up to 44 inches wide and gives you the drop you need as well, so it will work out very nicely. view full answer...
The umbilical cord between your motorhome and towed vehicle is going to sit the same way regardless of the hitch adapter since it's plugging into the 7-way on the motorhome and 6-way on the towed vehicle. Most tow bars are roughly 4' to 5' in length so you'd have a bit of wiggle room for the Blue Ox 7-Wire to 6-Wire, Coiled Electrical Cord # BX88206 to complete its connections and still accommodate the pull to left or right when making turns. view full answer...
I recommend using the Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets # RM82RR on your 2022 Newmar Bay Star 3226. This custom mounting bracket is specific Ford F-53 V8 22,000LB GVWR chassis. The Exact Center included is their heavier duty stabilizer providing you with the best steering feel.
I find installing the SumoSprings Front # SSF-170-40-2 and Rear # SSR-187-54-1 with the steering stabilizer will greatly increase your comfort level while driving. These help to absorb... view full answer...
A proportional brake controller will absolutely work on a motorhome like your 2021 Newmar Dutch Star with air brakes, as it simply needs to wire into the brake light circuit (the circuit that only sees voltage when your brakes are applied). So, the actual type of brakes on your motorhome won't be a factor, which means you can use the Prodigy brake controller you mentioned:
- Tekonsha Prodigy P3 Trailer Brake Controller # 90195
The P3 # 90195 is a great choice because it offers consistently... view full answer...
The Swagman Dispatch 2 Bike Platform Rack - 2" Hitches - Frame Mount # S44FR will be about 33 inches from the hitch pin hole to the farthest point of the rack. You will need to measure your tow bar to see how much actual clearance that will give you for turning clearance. This rack does have a shank rise of 6-1/4 inches, so that will possibly help with hood clearance as well.
I recommend using a shank like the Replacement Shank for Gen-Y Adjustable Ball Mount - 2" Hitch - 10" Drop/Rise... view full answer...
Typically if your motorhome is leaning one way it just means either the manufacturer or you have it too much loaded on one side, but this could also be an indication that there's an issue with your suspension so I highly recommend everything is is in good shape and that nothing is damaged before adding on anything.
Once you know your suspension is in good working order then yes, I definitely recommend installing some SumoSprings. These will give you a much smoother ride over the Timbren's... view full answer...
Manufacturers do not list the model numbers of the entry door locks so to know if the Bauer Products Keyless Entry Motorhome Door Lock - Left Hand - 8" Wide x 5" Tall # BA46FR will work with your 2022 Newmar 4037 you'll need to remove the existing door lock and measure the cutout hole.
The # BA46FR requires a cutout hole dimension of 4-1/2" tall x 4-7/8" wide and a distance from door edge of 1-1/8".
If your cutout hole isn't compatible with these requirements then just reply back with... view full answer...
Trailer brake controllers are not vehicle-specific so pretty much any controller could be installed in any vehicle.
All controllers use the same wiring colors and connections: the white wire is ground and connects to the battery negative post; the black wire is +12V power to operate the controller and this connects to the battery + post through a 30-amp breaker; the red wire takes in the brake light switch signal (taken from the cold side of the brake light switch); and the blue wire... view full answer...
The Parallax 7345 has a 45 amp converter in it so the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 45 Amp # PD4045KA you were looking at would be a perfect replacement for it. They'll just need to flip the small switch (pictured below) to the "LI" setting to switch the converter to lithium mode.
This unit requires a cutout hole 10-3/4" long x 7-1/4" tall, so they can remove the mounting screws of their current unit to measure the cutout and see if any alterations... view full answer...
I recommend measuring the feet on your leveling system and noting the shape of the pad. That said, it should be 9" round pads and in which case you would use the SnapPad XTRA Jack Pads for Lippert Leveling Systems part # SP54FR4.
If you have a different size/shape you can select this from the list below. view full answer...
The part you need for your motorhome is the Replacement Air Jumper for Demco SBS Air Force One Supplemental Braking System # SM99666. view full answer...
We can absolutely get you the correct SumoSprings for your 2018 Newmar Bay Sport 3307 motorhome, and what you'll need are the following part numbers:
- Front: SumoSprings Rebel Custom Helper Springs # SSF-170-40-2
- Rear: SumoSprings Maxim Custom Helper Springs # SSR-187-54-1
SumoSprings are a really smart choice to add to your motorhome, because they engage as needed to counteract sway, compressing based on the amount of weight being transferred. So when you encounter that heavy crosswind,... view full answer...
The Hollywood Racks RV Rider Bike Rack # HLY64FR is rated for RV use and will work with most RV's. The easiest way to determine your clearance would be to measure the distance from the hitch pin hole on your RV's hitch. The closest point on the Hollywood Racks RV Rider Bike Rack # HLY64FR is 12" from the center of the hitch pin hole.
We have not had the chance to test the Hollywood Racks RV Rider Bike Rack # HLY64FR on a Newmar specifically. But you are correct that there are a lot of... view full answer...
You would have to use a stacked receiver with a large enough rise to accommodate the bike rack sitting higher than the Kar Kaddy # DM9713093. I recommend one like the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers # 325-GH-316. This would allow you to haul a hitch mounted bike rack as well as the tow dolly. view full answer...
The Wiper Technologies Vented Windshield Wiper Blade # WPR26FR has a 21mm saddle. It uses a bolt on connection to your wiper arm on your 2016 Newmar Dutch Star Motorhome. view full answer...