Unfortunately we only offer Solera Awnings and components, which are not compatible with Dometic awnings so the only thing we could offer you would be a completely new awning like the Solera Smart Arm 12V Power RV Awning # LC517505. You can reach out to Dometic directly to see if they can offer you replacement parts, but with everything you're needing the cost of each item separately might end up being the same or more than just completely replacing the awning. If you end up swapping out... view full answer...
I'm assuming you're looking for an extra camera for the Rear View Safety Backup Camera System # RVS-770613-213. You can add an additional camera with the # RVS-771. view full answer...
The Adco SFS AquaShed Cover for Travel Trailer, # 290-52243 that you refer to has one large area in the center of the street side cover. Please note the attached image.
When measuring for a trailer cover you want to measure from the front of the trailer box, not the tongue, to the rear including anything that is attached to the rear. This will include a spare or a ladder at the farthest edge at the rear of the trailer, measure the length, width, and height of the body.
I suggest you... view full answer...
Yes, you're looking for the TrailerLegs Tire Saver Stands for Trailers w/ Leaf Spring Suspensions # 326-TRLLG-6, which is rated for 24,000lbs and comes with 6 stands. view full answer...
There actually isn't a non-Pro version of the Lets Go Aero V-Lectric FAT PRO Bike Rack for 2 Electric Bikes # LGA77FR that you referenced so if this was the rack you are looking for it would be the one to go with. view full answer...
There are a couple of things that you'll need to know that will determine whether or not you can flip the axles on your 2017 Keystone Sprinter 5th Wheel. You will need to have round axles with either 2-3/8" or 3" diameter, and your current suspension system must be installed below the axle. You'll want to check the specs on the plate or sticker in the middle of your axle to determine what type of axles you currently have on this trailer to determine if your trailer meets these requirements.
If... view full answer...
To my knowledge the only sensors available for a Lippert OneControl system are propane tank sensors. In-Command is ASA Electronics' system, which also does not currently have a separate waste holding tank sensor that's compatible with it.
A separate system like the SeeLeveL RV Holding Tank Monitor # SE47VR is going to be the best option to give you the most accurate reading of your holding tanks. There's a few different options when it comes to these systems so that you can control your... view full answer...
The Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover, # FVU1500WH fits all Fan-Tastic Vent trailer roof vents and also works with vents from other manufacturers that measure 14-1/4" x 14-1/4" at the roof opening.
If your existing vent is screwed onto your roof, you will not need to drill holes to install this cover. Simply use the existing screws on each side of your vent and some caulk to attach the 4 mounting brackets included with the Ultra Breeze. Then secure the cover to the... view full answer...
The Trailair you have now is our part number # LC158778 which is a different fit from the # LC155943 you referenced. If you were looking to replace the pin box you have we have the upgraded Flex Air part # LC369535 with same 21k capacity but has additional cushioning over the standard Trailair. The Flex Air has a pivoting king pin plate that is cushioned so you end up with forward and back cushioning as well as up and down like the Trailair you have now. view full answer...
The closest available option we have to the specs you listed is the Redline Wet Bolt # 34007-187-00. This bolt features an overall length of 3-5/8 inches and has a 9/16 inch diameter. It does have a grease zerk to allow for easy maintenance.
This is designed to fit 1-3/4 inch wide double-eye leaf springs. I have attached a short video review that you can check out as well. view full answer...
The Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide, # 13703. Is our only option for that width, rated at max TW of 350 lb. Anything for that span exceeding 350 lb. will probably need to be custom fabricated. view full answer...
For your 2021 Keystone Passport SL Travel Trailer with an entry height of 32" and door width of 24", yes, the correct SolidStep Manual Fold-Down Steps is option, # LC698799. Currently these are not in stock. However, I do have a couple of viable alternatives to suggest. The MORryde StepAbove RV Steps, # MR98RR is for 23-3/4" to 26-1/4" wide doorways and entry height of 32"-33". There is also the Strut Assist version of this model step in, # MR45RR. Plus an additional option of the Handrail... view full answer...
We do have a couple options to lift your 2005 Keystone Cougar 5th wheel. The first would be to "flip" your axle using an over-under conversion kit. This moves your trailer's leaf springs to the top of your axle and will increase the height of your trailer the equivalent of the diameter of your axle plus the height of your leaf spring stack.
- Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00 (For 2-3/8" diameter axles)
or
- Dexter Trailer Springs Over-Under Conversion Kit #... view full answer...
The Furrion Chill Premium RV Air Conditioner System - Single Zone - 15,500 Btu - White # FR55PV is offered in black with the part # FR23PV. view full answer...
Yes, the Coleman Adapter Wiring Kit for Furrion Chill RV Air Conditioners # C-FACR15SA-A01 is exactly what you are looking for. This plugs into the current wiring you have now in your Keystone and into your new Furrion unit and will allow for an easy install and all of your current Coleman controls to function the Chill AC. view full answer...
The MORryde 10" Shock Absorbing Equalizers # MR54AR are currently our only 10" cushioned equalizer. The Road Armor # LC696740 is only available in the 6" length for tandem axle trailers.
I recommend using the MORryde Suspension Upgrade Kit # MR46ZR with the equalizers. These will allow the suspension to travel more freely and get the most our the cushioned equalizers. view full answer...
We offer the Lippert Components High-Speed Power Stabilizer Jack # LC369774 that you are looking for. The price is down on the product link of this page which is also where you can hit add to cart so that you could order it from us. view full answer...
Since we know the axle capacity of your 2018 Keystone Alpine 3701 is 7k the correct kit the Hydrastar part # HSE7K-T1 which comes with absolutely everything you need. Oil bath hubs, the Hydrastar actuator, and everything else needed to install it. view full answer...
The Replacement Ball Mount Hardware Kit for Reese Steadi-Flex Weight Distribution Systems # RP58528 is the only way that we have the clevis pins that hold the spring bars in on the Reese Steadi-Flex Weight Distribution System available. This is how they are provided to us and we do not have them available separately. view full answer...