Those don't fit a 2008 Ford F-250. Instead you will need the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers item # AL88398. These work with the 4WD models and have the same 5,000 lbs capacity. If your F-250 is a 2WD you'll need item # AL88212.
Since your F-250 has a 4-1/2" lift you will need to add a spacer to the rear end to compensate for the extra space in the suspension. There's two options and which one you need will depend on how tall the lift actually... view full answer...
Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you are not towing your trailer. These significantly affect the range of your suspension which can leave you with a stiff rigid feeling in the rear end. Plus if you hit a bump while there's weight on them they tend to bounce.
Instead, I recommend the SumoSprings... view full answer...
The etrailer # e88AR is actually identical to the Curt # 13028. It will have the same 4-1/2" - 5" measurement and 7" measurement you have from the Curt. view full answer...
The chart is just giving you the max capacities for different distances when installing the Fulton Fold-Away Coupler Hinge Kit for 3" x 3" Tongue # FHDPB330301.
For me it's easier to ignore the chart, and just use the table on the side. The distances (Max Pivot Length) are simply the distance from the center of the coupler ball back to where the furthest pivot hole will be of the # FHDPB330301. Basically you can just measure the right distance for your trailer tongue, put the coupler hinge... view full answer...
Yes we do Danny, check out the Optronics LED Trailer Tail Light # STL78RPG. This is a submersible LED tail light that has 10 diodes, a 3 wire design, and measures 7-9/16" long x 3-5/16" tall x 3/4" thick. view full answer...
Patrick, a green coffee pot no, unfortunately. We do have the GSI Outdoors Camping Coffee Percolator # GSI28MV which has a 6 cup capacity but is stainless steel, or, we have the GSI Outdoors Camping Coffee Percolator # 37325254 which is green, but has an 8 cup capacity. view full answer...
To find which steps fit your Intech Sol Horizon Rover you will have to measure. The Lippert pull-out steps attach the underside of the camper chassis, directly beneath the doorway. To decide which size you'll need, locate the space available underneath your camper that lines up with the door frame, and measure the width and depth.
To determine how many steps you'll need, measure from the mounting point to the ground. This is called the entry height. The entry height should roughly match... view full answer...
Hi Robert,
So I know you don't want to, but the only option for a hitch extension for your 2-1/2 inch hitch does reduce the receiver to 2 inches. I hope you're not mad at me, but there unfortunately is no 2-1/2 inch hitch extender that also has a 2-1/2 inch receiver. So if you do change your mind, what you can do is use the extender and a new 2 inch hitch shank:
- Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches # C45048
- Curt Welded Weight Distribution Shank # C17123
The... view full answer...
The answer to your question depends on where the hitch sits on the Bronco and how far the tire sticks out. This is not information that we have so you will have to use our measurements to compare on your Bronco. The distance from the center of the hitch pin hole to the closest part of the Kuat Piston Pro # KU76ZR and Piston Pro X # KU98VR is 10-1/8". If this is enough to clear the spare then it will work.
More than likely you will need additional clearance. In this case, the best solution... view full answer...
Hey Shawn, the Lippert 1621 5th Wheel Pin Box # LC1191191 that you referenced does not have stated pin weight capacity so as long as the trailer's overall weight is less than 15.5k it would be safe to use. Typically pin weight is 20 percent of the total trailer weight. view full answer...
Hey Rose, based on the dimensions and color you mentioned the correct slide topper for your 2024 East to West Alta is the part #LCV000163292. view full answer...
Hey Ken, we have verified in the pas that the Camco RV fridge vent cover part # CAM42163 works with the Atwood fridges like what you have and is black in color.
The Lippert steps part # LC432690 that you referenced would also work great as a replacement step setup as well. This matches the dimensions you need and would work great. view full answer...
Yes, the MORryde ALLTREK 4000 part # MR89DR is correct based on your dimensions. The ALLTREK provides best cushioning vertically and horizontally so it would be your best overall option. It would perform better than the CRE3000.
You'd want to go with the longer shackle kit part # MR76ZR.
The reason your wheelbase is a little shorter is due to your leaf springs being a little shorter than most. Typical size is like 25-1/8 inch or 26 inch. view full answer...
The etrailer Trailer Coupler # CTA-400 uses the Replacement Mounting Bolt with Nut for Adjustable Channel Couplers # MBT58500-LN58. This is a 5/8" grade 8 bolt. I have attached a diagram below which shows the full dimensions. view full answer...
All you're going to need to do is take note of the shape, the amount of jacks you have and measure the size of your jack feet.
For instance, if you had 4 6" square feet then you could use the SnapPad XTRA Square 6 Jack Pads for Lippert Leveling Systems w/ 6" Square Jack Feet # SN99FR you were looking at. view full answer...
According to Lippert the 68" Wide Thomas Payne Trifold RV Loveseat # TP59FR has the following sleeping dimensions:
- 56" x 70" x 19" (W x D x H)
So as far as the "length" term you referenced I believe the 70" is the dimension you're looking for. view full answer...
Hi Bob,
I drew up a little diagram below of the Curt Trailer Hitch Receiver # C13361. Each measurement is from the center of one hole over to the center of the other hole. If you need anything else just let me know. view full answer...
BAK offers their BAKBox 2 Collapsible Truck Bed Toolbox # BAK92201 which is compatible with the BAKFlip MX4 Hard Tonneau Cover # BAK48203 you found for your 2020 Ram 3500. This is really the best option since you can't use a crossover style tool box with the cover and any other box would have to mount to the bed floor which would then make your bed even shorter for loading long items such as plywood or other lumber. view full answer...