When you order the # TLF2007 you will receive two of the tie downs. Basically it's all you need for the front, so it's both sides.
You would need to order a set for the rear of your truck based on the truck you are driving. view full answer...
The SuperSprings Custom Suspension and Sway Control Kit, # SSA15MXKT, will include two SuperSprings that are designed to be mounted on the rear leaf springs of your 2008 Ford F-250 or F-350 Super Duty.
The kit will include U-bolts, shackles, polyurethane mounting base, and bolt hardware to install on your vehicle. Some components may not be used depending on the year, make, and model of your vehicle. view full answer...
Nothing else is required for your 1999 Ford F-350, and nothing further is needed to purchase - no adapter or supplemental equipment at all - in order to install the Curt EZr Double Lock Underbed Gooseneck Trailer Hitch with Installation Kit # C60685.
The hitch is the complete kit, and will fit your '99 F-350 perfectly.
The only thing you may be interested in is a gooseneck wiring harness for your F-350 if you don't have one, the Curt 5th Wheel/Gooseneck Custom Wiring Harness with 7-Pole... view full answer...
The pull pins that connect the hitch to the rails is something that comes with the 5th wheel trailer hitch but not the installation kit. If you need a set of 4 pins and clips you can use # 6014. The pins are 1/2 inch in diameter and 3-1/4 inches long. view full answer...
The two part numbers you mentioned would be representative of the same thing. The bwrvk35 isn't a standard B and W part number so the part # BWRVK3500-5W would be what you are looking for which is a 20k B and W Companion Slider hitch.
I attached a review video for this for you to check out as well. view full answer...
The Stromberg Carlson 100 Series 5th Wheel Tailgate, # VG-97-100, comes with all of the hardware needed for installation on a 2011 Ford Super Duty. We do have a few other tailgate options for your truck and all of them do come with the necessary parts for installation. I have included a link to them for you. view full answer...
The Triple LED Trailer Tail Light - Stop, Tail, Turn, Backup - Red and Clear Lens Item # CE44VR is sold individually. If you needed two you'd need to order a quantity of 2. I attached a picture of a similar Command Electronics from the back as well. view full answer...
For just the center section of the B and W Turnoverball part # BWGNRK1111 you'd want the part # BWGNRC800. We checked with B and W to confirm that this is the correct part number. view full answer...
The Redline 1" Long Black Torx Wall Liner Screw, part # WLS100, is sold singly. This way you can order just as many as you need.
If you need a screwdriver bit for these screws you will want part # TX425. view full answer...
The weight distribution shank and weight distribution head are included with the Reese Steadi-Flex, part # RP66558, that you selected. The only item you will need to complete the installation is a properly sized hitch ball to match the coupler on your trailer.
If your trailer has a 2-5/16 inch coupler you will need the Hitch Ball with 2-5/16 inch ball, like part # 63847. If your trailer has a 2 inch coupler you will need the Hitch Ball with 2 inch ball, like part # 63845.
If you have... view full answer...
The Draw Tite Hitch Spare Tire carrier part # 6715 does include hardware for securing the wheel to the mounting surface. If you check out the review video I attached you can see the nuts and bolts laid out on the table.
You may also want the locking hitch pin part # 63232 which also is an anti-rattle device that will take out all of the movement between the hitch and the rack. I attached a review video for this as well. view full answer...
The Bargman Triple Tail Light w/ Backup part # 30-84-103 is sold individually. Therefore, if you need one for the driver and passenger side then you will need to order a quantity of two. view full answer...
The Titan V-Bar Link Snow Tire Chains # TC3831CAM come with the crescent-shaped cam tighteners built into the chains themselves, and the L-shaped tightening tool that is shown in the linked video is also included with each set of chains.
This particular set of snow chains features V-Bar links for grip on snow and ice and is rated for driving speeds up to 30 mph. They are suitable for highway and off-road use. These chains will fit a range of tire sizes from 275/65-20 through 385/65-10... view full answer...
The plates you referenced that come with the Trailair Flex Air 5th Wheel Pin Box # LC328492 are spacer plates. If they would be needed they would mount between the trailer frame and the pin box. view full answer...
Yes, the item you selected, Tekonsha Trailer Breakaway Kit, part # 50-85-313, comes included with a 5 amp battery.
I have linked and FAQ Article on trailer breakaway kits and a video review and installation of the Tekonsha Trailer Breakaway Kit, part # 50-85-313. view full answer...
The WeatherTech Bug Shield # WT50035 does not include any accessory items but does come with an installation kit that includes fasteners and automotive tape. The shield installs without any drilling required. view full answer...
The Titan Chain Alloy Snow Tire Chains - Diamond Pattern - Square Link - 1 Pair # TC2526 comes with the chains, the plastic case, and the couple of links you see in the product page photos. These chains are made of manganese nickel alloy steel so they are very strong and durable.
If you need extra links at any time in the future, the 2-Piece Chain Link Set for Titan Chain Diamond Pattern Alloy Tire Chains - 0.218" Thick # TCRK-2 is also available for purchase. To make repairs you may... view full answer...
The carriage bolts, washers and spacer blocks that are included with the Curt 25K Gooseneck Plate, # 16055, only need to be used if you have a 4-bolt base rails installed on your truck. You can tell if you have a 4-bolt kit if you only have two carriage bolts holding each base rail to the frame brackets . I have attached a photo showing the difference between 4-bolt rails and 10-bolt rails.
The two additional bolts will need to be installed in the center holes on the base rails if you... view full answer...
Actually the Strait-Line Weight Distribution # RP66130 does not come with a shank so if you needed one for a 2-1/2 inch hitch you would want the part # RP54977, or if you have a 2 inch hitch you would want the part # RP54970 instead.
I attached a review video and installation instruction links to the right for you to check out plus an FAQ on weight distributions systems. view full answer...
The MaxxAir FanMate Rain Cover # MA00-955003 does not come with the bug screen included. For that you would need to add part # MA00-955203. view full answer...