To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
3,000-lb Capacity. These hollow rubber springs sit above the rear axle to help stabilize and level your vehicle. They also provide a more comfortable ride by absorbing road shock and improving roll stability.
Features:
Specs:
Whether you're hauling heavy loads in your bed or cargo area or you're towing a trailer, you will often see the rear of your vehicle sag while the front end rises. In these cases, the rear axle is handling not only the weight of the cargo, but also more of the vehicle's weight. Because less weight is on the front axle, the front tires are making less contact with the road. Overall handling - traction, steering, and braking - is negatively affected. But the resistance from Timbren's Suspension Enhancement System works with your factory suspension to keep your vehicle level and improve your driving experience.
The Timbren system comes with custom-fit brackets that are bolted onto each frame rail above the rear axle. Hollow rubber springs are bolted to the bottom of the bracket and hang down to where the bottom of the spring sits, 1" above the axle. The inch of clearance allows the existing factory suspension to operate normally under light loads and standard terrain, ensuring the smooth, comfortable ride that you are used to.
Timbren Suspension Enhancement Systems are designed to work progressively. When the hollow rubber springs are compressed, the convoluted design causes them to quickly collapse along the folds. Once the folds are compacted, the stacked barrel shape increases resistance, stiffening the suspension and keeping your vehicle level.
Each hollow rubber spring works independently to support the driver's side or passenger's side of your vehicle. This is helpful when you swerve or make sharp turns. Each spring is activated when it is needed, so body roll is greatly reduced. The independent action also works well when you are hauling off-center loads.
Because the vehicle handles better with the springs, less turbulence will be passed along to the trailer, and this helps to keep the trailer in line. Your driving comfort is further enhanced if the trailer does begin to sway (from a gust of wind or a passing semi), because the movement from the trailer is not transferred to your vehicle. This also works to make the sway subside more quickly.
Another great feature of the rubber construction is that the springs absorb most of the road shock, creating a smoother, more stable ride overall. Wear and tear on the factory suspension is also lessened because the rubber springs work to prevent bottoming out on rough roads.
Timbren's Suspension Enhancement Systems are much easier to install than air springs - there are no air hoses to run, no compressors or gauges to hook up, and no manual adjustments to make. The rubber construction makes Timbren's springs more elastic than similar products constructed of microcellular urethane. And more elasticity allows for a more comfortable ride because the rubber has more travel.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey guys, it's Jake here with etrailer. Today we've got John with us from Timbren. He's gonna tell us a little bit more about what separates Timbren from the competitors. I appreciate it, I'm glad to be here. Timbren is a suspension specialist. We're based in Whitby, Ontario, so we are a true manufacturer in Canada and we offer a wide range of suspension products from light duty, from commercial all the way up to Overlander, Sprinter applications and trailers.
Now we've talked about a few of the options you guys have and we have plenty of options on our website. Right. We've got the SES kits. We've got the axle-less suspension. Right.
We've got your new coil inserts that just came out recently. But what would you say is your bread-and-butter at Timbren Yeah, no, our SES, suspension enhancement system, is definitely our bread-and-butter. Came out in 2011, won a SEMA New Product Award for best truck suspension. And really, the evolution you just mentioned here, you know, starting in 1968 all the way through now, 2024. But the SES kits are really the core of who we are.
And if you, if you would say at, in the level of stiffness on the market, what would you, would you put yourself in more in a heavy duty side for the SES kits or is it more of a lighter duty Yeah, great question. Lighter duty, we certainly can have a product for commercial and heavy duty, but in '82 when SES was introduced, it was purposely introduced for that, that light duty market. So we start with 1500 and again, go all the way up, but by far really popular with that 1500, 2500 crowd. That kinda leads me into my next question. So we talked about, your specialty is kind of in the lighter duty, but do you have an option for the heavier duty for your sprinter vans and maybe for your truck bed campers Yeah, absolutely.
We do have SES kits for truck beds, truck campers with a higher center of gravity. That creates a new kind of set of problems with the sway side to side. So we have severe duty kits for those. And it uses a single convoluted AON versus a double convoluted to tackle that problem of side to side. And the same thing with the sprinter van. It uses a rectangular shape Aon, but it's there to do the same deal that side to side sway because they're so top heavy, it'll eliminate that. Okay. And then we've had an instance here at etrailer that we had a van that was very, very heavy on the one side. Is there anything that you guys can do personally to help, I would say, I guess customize that kit for that particular user Yeah, by all means we would want that individual to contact us. We would ask a couple questions, see where that weight is distributed and we can actually produce an AON with either a stiffer hardness or durometer or a softer durometer and that will help level it out. So yes, we can take care of that for 'em. And I think that'll really, really help people to get their rigs dialed in because who knows what they're putting in the campers afterwards, after they buy 'em. They come from the manufacturer already heavy on that side and they're trying to load stuff on the other side to try to even it out. But knowing that there's a solution that you can customize for your rig no matter what the weight is on either side is really, really cool. Yeah, absolutely. We're happy to take care of 'em and again, there's no charge for that. Awesome. Now to kind of wrap things up, what sets Timbren apart from a lot of other manufacturers out there Well, I think there's a couple things. We're a family run company and our longevity, you can't deny, 1968 to 2024 and our warranty, we have a lifetime warranty regardless of how old it is. We will take care of it, replace it, limited lifetime warranty, and the hundred day money back guarantee. Very cool. And that's whether or not you're the first owner Right. And yeah, we're not asking for receipt, who'd you buy it from It'll be taken care of. Just give us a ring and we'll take care of it for you. Very cool. Well thank you again for meeting with us. Appreciate it. It was a pleasure to work with you. Thank you.
Average Customer Rating: 4.7 out of 5 stars (6031 Customer Reviews)
3,000-lb Capacity. These hollow rubber springs sit above the rear axle to help stabilize and level your vehicle. They also provide a more comfortable ride by absorbing road shock and improving roll stability.It does a good job of dampening the impact of a suspension bottoming out in a fully loaded vehicle. We have owned our 2005 MPV LX sine new and I have 3 children plus a sister-in-law who goes on camping trips with us. Through the years, I noticed that when fully loaded, the van started hitting the bump stops more often and this is felt as a violent thump when going over bumps or dips in the road. This was getting me worried that the springs and shocks were worn out so I had my mechanic replace both of these because on numerous camping trips, this never happened before. It only partially solved the problem. Then it dawned on me- my kids are now all grown up/heavier. I just wasted $2K on new springs/shocks. I tried rubber coil spring spacers and upgraded my Bump stops to sturdier polyurethane units to replace the foam rubber original ones but these did not help at all. I considered the Air spring inserts but was worried about their complexity, durability and difficulty of installation since I wanted a DIY solution. The Timbrens did a good job of softening the impacts such that my rear passengers immediately noticed the improvement. The suspension still bottoms out but the impact is now soft and it does not affect the normal driving dynamics of the vehicle when not fully loaded. Installation was so easy that I made my two teenage sons do each side to teach them a few life skills. I give the product a thumbs up. The only downside is they are very expensive for what they are made of- simple rubber, bolts and washers. To compare, I could buy two new tires for the price of this pair of SES Buffers. Save your money and try these before replacing the rear springs/Shock absorbers.
i recently added a power lift to my 2002 mazda mpv to carry my husbands new power chair. i needed these to prevent the sagging that occurred when just the class III hitch was installed. we loaded the chair on the lift once and i knew we could not leave the sagging that way. i did not want the maintenance of air shocks, air bags or air springs so i ordered these and am very happy i did. it keeps everything level with the full load on the rear and does not affect the ride when loaded or empty (with just the hitch). i would recommend these if you just put people in the back of any van.
Installation was very simple. jacked up van with floor jack i have with tire 1" off ground. i am not sure if my stock bumpers fell off or were stolen in the past but they were not there. i took off the one bolt (14mm), assembled the timbren ses with supplied long bolt (17mm) and left stock bumper mount on top (same orientation), used a deep socket (17mm) stuffed with a paper towel and short 3/8" extension and started the bolt by hand. then placed the 3/8" ratchet on and tightened it up.
NOTE: I visited the hardware store before I started, with the assembled timbrens in hand. I bought two 7/16" washers and two 7/16" split lock-washers because it looked like the bolts would bottom out on the un-threaded portion before fully tightening them up.
Sure enough, on the passenger side i had to add a 7/16" lock-washer to get it to snug up. There was alot of slack/play after the threads bottomed out on the un-threaded part of the bolt shaft. On the drivers side it did not need a lock-washer added. it tightend up without any play. I will check them periodically to see if they are coming loose. if so, I will place the lock-washer and the other flat washer I bought on both bolts, then assemble the rest and tighten up again with thread locker on the threads.
The install went so fast if I had to take them down to add anything it would only be a few minutes for both sides.
Nice stiff, controlled cornering without the roll. wish I added these years ago to make my minivan with the heart of a sports car even sportier. Thanks e-trailer, Carol S
Read a couple of peoples' install tips, and using them, install went pretty smoothly, lifted the van just right.
I haven't installed or used them yet but they seem well made and easy to install. Came with instructions.
Barry
12/26/2022
Working great.
2004 Mazda MPV rear suspension.
We tow a small popup with the aforementioned minivan. It would always sag in the rear by a good 5 - 6 inches. The Timbren cut that down to about 3 inches. It also helped with stability towing and carrying heavy loads whilst on the interstate. Unloaded it does make the ride a bit harsher, but it is a very good trade-off.
Installed on a 2000 Mazda MPV. Some installation comments. The shorter set of bolts specified in the instructions to fit are too short to be inserted into the bump stop assembly with enough bolt left protruding to screw into van frame. Used the longer set of bolts. The threads on the longer bolts reach their limit just as the assembly makes contact with the frame. With the bolts tighten snugly, the assembly can still be turned easily by hand. No significant play vertically. Performance appears to be fine.
Brooke M.
3/23/2023
Ope! Your review is blank. If you would like to add any comments, I would be happy to help you with that.
I know it will be lovely when loaded or the trailer on. However,it rides like a wagon empty with brand new premium shocks and struts empty. Thud thud thud. You really cannot feel the shocks or suspension. Found exact same item plentiful for 60 bucks on eBay after I bought these for 250. I may cut these in half or put air bag on. I do not like the ride empty. No hard feelings. It is a good product maybe just not for me.
About a 1/2 inch difference in gap at the bump stop perch but still within parameters. Truck sits perfect with trailer attached. Haven’t towed yet. After towing if they perform like they should will upgrade to a 5 star. Easy to install, definitely needed 2x4 and jack. 2011 Silverado ext cab with 30 ft Genisis 5th wheel.
Was able to install these with a 15mm flex head ratchet wrench and lifted the rear of the truck to make it easier. 30 minutes to take off 4 nuts and put em back on. 2 minutes assembling the timbrens with the added spacer. I have a f350 with a salter and plow. Loaded with salt the lights shoot up and in the snow ?? it’s like hitting hyper drive and you’re blinded. These helped big time. Very happy so far.
The pro: The longer, heavier bump stops worked great when hauling my mustang home from Chicago. The truck stayed level and handled great.
The con: I had to remove the bump stops for everyday use. They limited my suspension travel causing a stiffer ride.
I am so glad I bought these for my truck. I was able to install them myself using a jack and jackstands. The ride is bit rougher now; but the suspension is totally awesome compared to before. I am able to haul a bit more weight when needed.
Haven’t had it on long, but so far so good. 1999 F350 dually. Bolted up nicely. Total job took 10 minutes. Have hauled two gooseneck loads of hay and truck drives SO much better. Nice and level. Money well spent so far.
very good product ,received just in time and fit perfectly on my GMC savana 2000 .Be sure to clean the two receptacle thats help.
très bon produit , reçu dans les délais et s'ajuste parfaitement . Assurez-vous de nettoyer le receptacle cela facilite l'installation.
The timbrens actually did what they were suppose to do. However, once I starter driving out west I notice the timbrens were riding on the axle which cause the speedometer to jump around depending on the road. I would recommend them if you are hauling or towing a camper or RV. I was going to contact etrailer about maybe removing a spacer for one set however the other set came as one unit. The bottom line is the Timbrens does stabilize your load for safe travels. I will be contacting etrailer soon to assist in correcting the problem...Road trip from Idaho,Colorado,Wyoming,and Utah were beautiful... Thank you etrailer
Definitely a must have when towing..stiff without a load but night and day difference while towing my travel trailer, better traction, steering and braking. Easy quick install..only issue I had was with the long bolts they sent with the spacer kit (optional for lift) the bolt diameter was too wide to fit through the holes on the bracket..but a trip to the local hardware store took care of that.
Pros: Cheaper and easier to install than airbags, do the job when load is enough to compress the shock, with added weight or towing, then it stiffens the rear very nicely.
Cons: Doesn't do anything until there is 2-3cm of compressed shock. It sits above the contact point, doesn't touch. Under normal driving, there is no benefit/improved stiffness/anti sway in rear or a leveling of the factory rear sag in a 2022 or newer Toyota Tundra.
If had it to do over, would have put some kind of spacer in between product and upper included bracket, the supplied bolt is long enough to accommodate, to eliminate the gap, and lift the rear 1-2 cm. Should do it anyway, maybe when swapping to summer wheels next month.
I’d seen similar products rated in the 4,000 lb ratings but I went with these. I’m not a mechanic but I removed the factory bump stops and installed both these in 30 minutes or less. I used my rolling jack and lifted from the drop hitch and easily removed the old ones and soapy water and 1/4 twist and these were on. Placed a block of wood in the space between these coils and lowered the jacks then pressed it with my tractor to confirm full engagement. I carry a lot of tools on a 2020 Chevy 2500 I do feel a bit of butt bounce on large bumps but other than that I’m very pleased.
The order with Will at etrailer was great. He was very helpful and knowledgeable, Installation was not easy but not too bad, The hardest part was removing the factory pieces I removed them from below which was a blind nut removal operation. This is on a 2017 Mercedes Sprinter motorhome. After removal of the factory pieces I discovered that access is much easier on top between the tire and the mud flap, I turned the front wheels inward and they didn't have to be removed. The front of the motorhome had to be raised quite a bit to get the Timbren piece jnserted. Also I learned to tighten the bolt and nut in the Timbren bumper as much as possible before installation because there is no access to the bolt head when tightening the top nut to keep the bolt from turning, preventing tightening the nut.
First off the product was beat up with paint/power coating missing in several places on both. I was putting on a brand new truck with less than 800 miles on it so I elected to touch up before install. I’ve hear a lot about Timbren but never had them. I had airbags on my F350 but when I switched to a new Tundra I went with Timbrens. I’m a bit disappointed in the ride. Feels like I can feel a “bump” in the truck from the rubber pick hitting the axle when I go on a bumpy road. Thinking I should have went with airbags. As far as having a load on the truck and helping with the squat, they do as they are advertised.
I bought these to prevent the "squat" of carrying a load in a Ram 1500.It took only 30 minutes to install. Now when carrying a load or towing a travel trailer the truck is a better position.
The only thing you will notice is the smoothness of the ride. It's not, it is stiff. I'd rather have the stiff than the nose pointing to the moon.
These work great for giving you a solid towing experience when loaded heavy; however, when driving empty you definitely get the jounce bumper “into the air” experience when driving on moderate to rough roads. I have the recommended gap installed between the axle and the timbrens, but with terrible midwest roads and highways it doesn’t seem to be enough gap. Smooth roads it rides great. It’s driving 80mph on the expressway and hitting potholes or large cracks where these will hit causing uncomfortable harsh ride.
I’ve resorted to installing and then subsequently removing these anytime I use my travel trailer for longer trips (30minute removal time). I tow a 7000lb loaded travel trailer with an f150 and just needed something to make the soft half ton suspension from porpoising too much on bad-roads. Mission accomplished when towing as I said these things work great for heavy loads. It almost rides better with heavy loads…. I was going to give airbags a try but the reviews from others have scared me from those because even with airbags at the lowest setting you still get the jouncing on bumpy roads.
Easy install took about 20 minutes on my 2017 Ram 3500 SRW. Had about 1/2 inch clearance as recommended. Loaded up my 5th wheel (2350 hitch weight) and about 200 lbs of gear in the bed. Just got back from a 800 mile camping trip through mountains of TN. You can really feel the difference around those sharp corners and uneven surfaces. The truck felt firm and controlled not hard and jarring as some have mentioned. Going over those overpasses with the wonderfully smooth (Not) joists was greatly improved. The truck would squat and rebound again, with a firm controlled response. Driving without a load felt the same as before without them. I would highly recommend these! Ordering from etrailer continues to be my go to option!
They do exactly what I wanted them to do. They support my boat trailer and when not towing, they don’t touch the bumpers everything’s great.
This kit installed easily on a lift; just use a pry tool to pop out the factory bump stops and press the Timbrens in their place. The customer was using the vehicle to carry heavier loads and needed to reduce rear end sag that was causing clearance issues with the ground effects that were part of a wheel chair accessible customization that had been previously added. The timbrens did the job. It would be nice if this kit offered some adjustability on height so one could control how much the body dropped before the timbrens engaged. That is a suggestion for Timbren and not etrailer.
Do you have a question about this Vehicle Suspension?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Donald
8/14/2023
They allow me to xarry greater loads than I would be able to without them.