Summer Starts Here - Save up to 70%
11" Wide x 8-3/4" tall x 7/8" deep, efficient heat exchanger will prolong the life of your transmission and improve its overall performance. Specifically designed for vehicles with late-model, electronic overdrive transmissions.
Features:
Specs:
One of the more popular cooling systems available, the radiator-style, plate-and-fin heat exchanger provides increased surface area so that fluids can spread out along the finned chambers to cool faster. In addition to the increased surface area, this cooler also features turbulator technology, whereby fluids are agitated continuously, not only to facilitate heat transfer, but also to prevent any undesirable drop in pressure.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we'll be taking a look at the Derale Series 8000 Plate-Fin Transmission Cooler with Barb Inlets. This is a Class IV transmission cooler and basically this is going to help to prolong the life of our transmission and improve the overall performance that we get from our vehicle by preventing any kind of heat related failures. This is going to cool down that transmission fluid as its flowing through our vehicle. A lot of times if you're trying to get the most out of an older vehicle, maybe it's seen a few years and it just needs all the help it can get or you're using your vehicle to do some medium to light duty towing. This is going to help to make sure that we don't have to cut our vacation short or cause any delays by having to deal with a overheated engine.So it's the plate-fin style, it's going to be the plates running across there. Those are turbulator plates for more efficient cooling.
They're 3/4" wide. Turn it to the side, those are 3/4" wide there and then we'll have all the fins sort of running back and forth like little ribbons in there. That helps to increase the overall surface area to cool everything down more efficiently and a lot quicker than we typically get from our transmission as it is.This is recommended for medium to full size cars and intermediate SUVs that are again going to be doing some light to medium duty towing and just trying to get the most out of those vehicles. We'll have our inlets which are 11/32" hose barbs. The gross vehicle weight rating for this is 20,500 pounds.
As far as the overall dimensions, it's about 11" wide from the outside edge of those inlets, and then if we turn it on to the side from the top of the inlet to the bottom of that cylinder, it's about 8-3/4" tall. If we go from the top of the inlet to the bottom of the mounting flange, it's a little bit longer and that would be about 9-3/4", or about 9-5/8".Our thickness overall, it's about seven eighths of an inch to that outer cylinder. The distance between the inlets, center to center, is about 10-1/4", and then for our mounting holes, the distance between those at the widest point, center to center, again it's about 6-3/4", and then for the two narrower ones it's about 5-1/2".If you want to get a complete installation kit that comes with a hose and some mounting hardware, you can find a lot of options available here a etrailer.com. One of those would be Part Number D13006, that's going to come with some of your 3/8" hose that can withstand the heat of that and also some rods and other hardware to get this installed.Again, there's a lot of different configurations out there, so definitely search around at etrailer.com to find the right configuration for you. This does come with a one-year warranty.And that's going to do it for our look at the Derale Series 8000 Plate-Fin Transmission Cooler with Barb Inlets..
Average Customer Rating: 4.7 out of 5 stars (814 Customer Reviews)
11" Wide x 8-3/4" tall x 7/8" deep, efficient heat exchanger will prolong the life of your transmission and improve its overall performance. Specifically designed for vehicles with late-model, electronic overdrive transmissions.A very good product,installed very easy and keeps the transmission cooler while towing.
Works fine and wasn't difficult to install. I didn't take the bumper cover off. Worked from top and below.
Fashioned an aluminum brace.
I did not test my transmission temps before installing this cooler, so it's very possible that it is helping -- just not enough. 4Runners are not great towing vehicles to begin with, so it's probably not this product's fault. It's fine on flats and gentle inclines, but on long steep inclines I still find myself hitting 260 degrees towing a ~3,000 lb teardrop. If you're towing with a 5th gen 4runner I would look into something bigger or one of the options with a fan.
Very cool product! I can't seem to 'feel' the difference while driving, but when engine cold, the transmission shifts harder.....probably proof that the transmission fluid is not warming up as much
Thanks for shipping so fast. the response time was impressive!
Below is a picture of the install of my Derale trans cooler (13503) installed in my 2010 Jeep Liberty.
I did not install with the inlet/outlet on the bottom due to thinking that with a plate and fin type cooler air might get trapped in other end. I mounted it horizontal and put the inlet flow on the bottom to assure that any air gets purged. Odd thing about this trans is that there is a bypass valve on the lines that is thermally operated. The flow to the coolers is bypassed until a specific oil temp is reached. Then flow is allowed to go to the cooler(s). This is done because the trans cooler is completely independent of the radiator. There is no thermal exchange between the trans fluid and the engine coolant. With the transmission fluid bypass valve in operation it is not possible to reduce trans temp below a preset level (or nearer ambient temp) because the thermostat valve simply turns off flow to the cooler(s).
In a conventional setup the coolant flows all the time and there is no by-pass. Trans fluid is kept from dropping in temp by the engine coolant which will actually put heat into the trans coolant if the engine coolant is warmer. Chrysler has no thermal exchange with the engine coolant so they thermostatically control flow to keep the trans from operation at a too low temp.
In short, in my vehicle I can’t reduce the trans temp below the thermostat setting, But I can assure that the temp of the trans can never be too hot.
I also mounted the trans cooler on brackets I made. I was uncomfortable pushing the rods thru the radiator and the air conditioning and factory trans cooler. The added mass of the Derale trans cooler may have been a little too much clamped onto the radiator. I tapped into the original hose with a 3/8 double barb fitting and double clamped all connections.
Also below is a exploded parts view showing the by pass valve on the trans lines which directs trans fluid back to the trans and by passes the cooler(s) until the trans gets to a specific temp. It is item #3.
Part seems to be okay. The hose is to short. Now I have to wait a few days to receive more hose to finish installation. etrailer should add more hose than the length that comes with it. On many applications this cannot be intalled effectively with the amount of hose in the kit. This is even mentioned in the video that etrailer provide.
I installed the cooler last weekend in my 2008 Silverado. I've included some
pictures.
I made a strap to support the upper portion of the cooler and thru bolted
the lower to the existing bracket.
The hood bracket lower bolts had to be cut down to 1/4" length so they would
not contact the cooler.
The lower mount bolts had to be spaced to give the hood mount weld nuts
clearance.
Now to see how it does with a trailer and the Pacific Northwest hills.
Well constructed. Could use more hose for the install. I had to buy another length to install it. In the photo you can see I fabricated brackets for it so it would be able to get better airflow. Not noticing a real big difference in cooling but I’m anxious to see how it goes when I tow my 29 ft. TT with my 17 Suburban with a 5.3 ltr. I’ve been towing without one with no issues but any help in extending the life of the tranny is worth it.
Wil need additional hose and brackets for my install. Will get local but would have purchased if I knew they were needed
09' silverado 1500 5.3
Temps are down 15 to 25 degrees on test drive, No trailer. 105* heat index city, highway, a.c running
75mph 169-171* (factory 185*+)
55mph 165*
City stops 159*-163*
Idle after drive for 10 min in Sun 149*
Trimmed factory grill mount and welded on tabs, to put back in factory location (no picture of finished grill mount by itself) used factory holes on upper grill hood latch assembly. Only fault is u need to remove trans cooler to unbolt grill mount, but it's just a grill mount.
I installed this on my Toyota 1996 T-100 3.4: I picked up a piece of universal hangar strap, 2-8mmX1.25 bolts & lockwashers at building supply; 3 gal tranny fluid (flushing system including torque converter), 4' extra hose & extra clamps @ auto supply. I first mounted flange to central member with a couple screws; then bent 17-1/2" of the strap to pass the AC line ( the holes for the two bolts actually lined up to the two factory threaded holes available!!PTL). From there it's almost a done deal; hookup the cooler to the return side out of the radiator and let a half gallon at a time pump out till you get new fluid: then make up your return hose to the steel return line. It's oversize but this is FLA and it pulls. Heat is death to transmission fluid; and then the transmission! Good project.
Have a 1998 Lincoln Mark 8 w/ 4 speed automatic which retails for no less than $ 4000.00 - Having this potential monkey on my back , I decided to invest in a trans cooler. Fabricated mounts and bolted on , used double flare connection to cooling line w/ barbed fitting ; barbed fitting @ radiator fitting. Used 2 hose clamps @ cooler, one clamp on each barbed fitting . Could only mount with fittings to left ,fluid leaves radiator , enters cooler @ top ( to reduce pump load ), comes out of bottom & returns to tranny. No trans temp. guage, but cooler gets hot @ idle, verifying cooler works . Well constructed and sturdy,easy to mount ; comes with instructions.
It’s been almost a year since I installed this transmission cooler. I would say it’s gone without a hitch, but THAT would be inaccurate. I also installed a hitch! I placed great confidence in this transmission cooler to do its job as my 2015 Honda Accord V6 served as my truck during our move this past year. Never a problem (ok, I’ll say it... It went without a hitch!).
etrailer customer service was EXCELLENT! There was a question during installation that arose from my particular model of car having a Transmission Fluid Warmer that in effect made identification of the transmission outlet and inlet reversed according to the instructions. The technician actually read and considered what I was saying, instead of just assuming the instructions applied to my vehicle. Thanks to their input, I correctly reversed the directions and got the correct solution!
BTW... I attached some pics of the correct hose routing for the 2015 Honda Accord V6. Note how you simply remove the short hose shown in the first pic, and connect the hoses from the transmission cooler! Note that I mounted the transmission cooler vertically so the hoses would reach. The last pic is showing the transmission fluid warmer (just as an FYI).
This does not fit a 16 Pilot Touring. The only option is the OEM trans cooler (500.00).
My teenage son and I installed this on our 2010 Suburban in about 2hrs. This was to supplement the tiny, stock external cooler. The video was very helpful. We did not have to cut the plastic as in the video. There was enough room for the hoses and fittings with no kinks. The transmission was running hot, 190-200 degrees with no trailer and up to 220 degrees with a trailer on level ground. The transmission never got above 155 degrees, with no trailer, after this cooler. I can't wait to tow now. I am confident the temps will stay at or below 200. This is just what I needed for my lifted Suburban and travel trailer.
I installed this transmission cooler about a year ago. Install went easy but I did have The bumper off as I was replacing the radiator. I think my temperatures are down by about 15°. The only reason I did not give it five stars is that I probably could’ve used a larger one.
Transmission cooler installed on 2003 Tacoma RWD.
The Transmission Cooler was easy to install. No problems whatsoever.
I chose to mount it behind & left of the license plate.
Great product, really helped keep my trans temp down. I deleted the thermal device on my suburban transmission (sorta like a thermostat) and coupled with this external cooler my trans runs an average of 50 degrees cooler when towing, sometimes more. Definitely worth it.
First very easy to install. So for the quality is outstanding no wear or corrosion. Highly recommended
The hose that came in the kit was about a foot too short and should be 3/8 id. I had to source my own longer 3/8 transmission cooler hose. Other than that, the quality of the cooler appears to be good.
Although the website said this fit my car, it didn't. etrailer is good if you don't have to return anything. I've done a lot of business with them and have been satisfied but when I had to return this the return shipping was a third of the price of the item. Not good.
Transmission cooler installation on 2012 GMC Yukon 5.3L.
Top brace added for support.
I recently had the chance to use the Derale 8000 series transmission cooler during my last camping trip and was very impressed. I have a 2001 7.3 Powerstroke with 4" exhaust, S&B intake, gauges and a DP Tuner (60hp tow). I pull a 10,000 pound 5th wheel around Colorado. It seems like every where I pull in Colorado is up hill. It was common to see my transmission temp easily and quickly reaching 210-220 when towing mountain passes. Just before my last trip I installed the Derale cooler and the highest trans temp I saw was 190 at the top of Wilkerson Pass. What is more impressive was how quickly the temp dropped as I came out of the pass. For most of my trip my trans temp stayed around 180. While pulling in the city I saw temps around 200 which I assume was due to stop and go driving and not having the constant airflow through the cooler.
I installed the cooler right behind the stock front grill to the vertical post with self tapping screws (the grill still fits perfectly). I then used two thin strips of metal that I got from the hardware store and secured them to the cooler and to the second vertical post. I wanted the cooler in the front of my truck to get maximum airflow. I then spray painted the metal strips black just for looks. I did have to buy an additional 4' of hose due to the location where I mounted the cooler. The optional instal kit was simple. The adaptors screwed in my radiator with no problem at all. Once I decided to mount the cooler the entire project was quick and simple.
This cooler is working perfectly. It gives me piece of mind when I'm towing my old travel trailer. I didn't use the plastic ties that come with the product but instead mounted it with aluminum frame material from the hardware store. I was disappointed that the kit did not come with the adapter I needed to install it onto the transmission fluid lines on my Chrysler 300. I had to obtain the fitting from a salvage yard. The instructions were helpful.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.