To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
This aerodynamic, flush-mount roof rack lets you carry gear and cargo on your vehicle while maintaining a clean, factory look. Crossbars work with channel-mount and clamp-on accessories. Installs on your vehicle's naked roof.
Features:
Yakima BaseLine FX LG:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
How's it going everyone Today we are going to be taking a look at the Yakima JetStream roof rack system, installing it and explaining how it works on our 2021 Ford F-150. So, with the F-150 we have a good amount of bed storage, but if you want to get some longer or larger items, like say a kayak, or maybe you want to use this in conjunction with like a ladder rack system to get some longer loads up on top of your roof, this is gonna be a great option to do so. So, let's take a closer look at how it works. As far as the weight capacity goes of our roof rack system, it is really robust, but you want to keep a couple things in mind, that being the fact that the system itself has a weight, the accessories that you're gonna put on 'em. Also we're going to add to that, and your roof is going to be rated for a specific weight as well. Make sure you check the owner's manual in your case, find out what that weight rating is and make sure that all of the components, including the roof rack and the accessories don't exceed that limit.
They get the name JetStream because of this aerodynamic shape on our cross bars here. So you can see we do have this rounded portion in the front, and then it tapers towards the back. That is gonna help cut down on some of the wind noise and drag you get from putting something up on your roof, but you're still gonna hear it. This weather strip on the top is gonna help cut down on some of that as well. And this channel is also gonna be able to be used for your T Track accessories if your rooftop accessories do have that as an option, and the rubber strip will help keep them in place.
Underneath you will typically have another rubber strip that'll cut down on some of the wind noise. In our case, this is just for demonstration and we don't actually want to have to trim that up, according to where we're putting our towers every time. So, we don't have it on, but in your case you would. And again, that would help cut down on some of that sound and noise while you're driving. The system we're using today uses 60" cross bars, which I think is a really nice size for our F-150.
The overhang is enough that we could maybe get a clamp-on accessory around here if we wanna have easier access to one side, especially considering it is a pretty tall vehicle. but it's not so much that I'm gonna be worried about hitting my head or extending past the overall width of the vehicle. If we want to, I'll measure now just to figure out how much height we're adding total. So, from the middle here to the total height of the system, it's going to be coming in just under 4", that's how much height you're gonna be adding. So, if you have accessories, add that overall height to your cross bars to find out if there might be some clearance issues wherever you're going, or that number is just something you wanna keep in mind as far as, "Can I store these in my garage" Another measurement to get is how much space we have underneath, so that's gonna be about 2 3/4, that's how much room you're gonna have for your clamp-on accessories.
If you want to use those, you have tons of room for them to make clearance before they're gonna hit the top of your roof. Or if you have something like skis or snowboard bindings that you're worried about making contact there. Taking a look at our end caps, we have a nice glossy finish. Right here is where you would upgrade to metal lock cores if you chose to do so, which I would definitely recommend. And if I just pinch the top, I can pull this off and get this out of the way so we can see what this is protecting. It's going to be our fit kit hardware. All that we would need to do to get this on or off is store it in here. So, that's the job of the end cap is to protect that, keep that in place, and we'll take a closer look at all of that in the install portion. Talking about the fit overall of the bases. You can see how the extension on the pads here fit right into the ridges of our F-150. So as long as you take the time to get those measurements right, which we'll explain a lot in the install portion, it's gonna be a really nice solid fit. Something that's also unique to the JetStream system is how adjustable it is. It's got adjustable pitch and toe settings, so if you have different roof shapes, you can accommodate your cross bars to fit that really well, and it can definitely be a little bit daunting and a little bit tricky, especially when you see all those measurements. But we'll walk you through that process right now. First thing we like to do is just to lay everything out so that we know what and where it is. So, we have our cross bars set up here. We have the bases for the towers, we have our end caps here and here, the towers themselves. We have our fit kits for our faces, and we have the tool that we need to tighten everything down. But our first step is going to be preparing our towers. To get our towers on, first thing we'll need to do is get our end caps off. So I just like to use the tool they provide to get that initial tab loosened up, pop that off, and now we'll see on our towers, we have this metal plate here at the top. All we need to do is line that up and slide that into the channel underneath. And we'll do this on the other side as well. When getting your towers on there's a chance they might be too tight. If that is the case, release this security door here, that'll expose this bolt in the back and we can loosen that up with the tool if we need to, to help it slide up and down our towers. And now we're gonna find our M3 measurement, since this is gonna be our rear cross bars, and for that the number that we get is 47 3/4. So we can look at this ruler right here on the cross bar, find that number 47 and about 3/4 right there. Then we'll find that on the other side, and then we can go ahead and tighten this bolt down. In addition to this bolt tightening up our towers, this is also the pitch setting. So in the case of the rear crossbar, it's going to be B, which is going to be the one in the middle, so we're good to go. This front bolt is going to be the toe setting. In the case of our rear cross bars, that is going to be B as well, which is the middle. But it's important to know the orientation of your bars. So we drew a little arrow in the middle of ours. We want to know that the back is going to be C, towards the front is going to be A, same. The back is going to be three, towards the front is going to be one. So B and two are in the middle like we have them here. Now it's time to put our bases onto our towers. So we see this arrow pointing outward, we wanna make sure that lines up, if they're not already put together, it's just a matter of fitting this rubber piece onto this plastic piece and making sure that that's securely in place. Again, arrow out, fits right there onto our tower. Just snap it down in place and we'll repeat that process on the other side. With our pads and our towers both in place and in the right position, we're going to get our bar up on top of our roof. We wanna make sure that we have the rounded side towards the front and the taper towards the end. And we're just going to guide it slowly, using those pads to take a lot of that weight for us, get it roughly into place, but its measurement is going to depend on where the front crossbar ends up, so let's move on to setting that one up. Up until this point on our front cross bars, the whole process has been the same. We put the pads on our towers, put the towers into this channel underneath our cross bars and we even have the same measurement, as far as the strip goes underneath. So, the first difference that we're going to run into is our pitch setting. In this case, we want the pitch setting to be A, which is going to be the direction closest towards me. So I need to push this down, or maybe loosen this up just a little bit so that we can get that over there. Now you see we're at there, but I actually slid mine a little bit down this track so I wanna make sure I find that 47 3/4 mark again before I tighten everything down. So right there is good. We're at A here on a pitch setting, so we're gonna take the provided tool and tighten everything down until it clicks, just like we did on the other steps. As you can see here, on our toe setting, we have shifted forward. We actually want that to be two, which is the one in the middle. So I'm gonna loosen that up just a little bit and I like to use the tool just to push that down. So just like that. Now our toe setting is back in two, and our pitch setting is in A, and we're going to repeat this process for the other side. Keeping in mind if you don't have access to that bolt, all you need to do is open the security door with our bases, our towers in place and the measurements and pitch and toe settings correct. We're going to get our front crossbar on and roughly in place, same process as the back, making sure that we have that rounded part facing forward and the taper towards the end. And now we'll get our first real measurement. This first measurement is going to be from the corner of this painted roof here right until the leading edge of our cross bars. So I'm going to look for the number, in our case, of 8". So I'll set that up. Again, we're just using the fabric tape measure. You can use the one provided. We're using our own, so we need to slide this up just a little bit and then I'll go to the other side and adjust it accordingly. After we get our front crossbar on and in place, and in the correct measurement on both sides, we'll get our M4 measurement. In this case, from leading edge of the rear crossbar to leading edge of our front crossbar. We want that to be 32". So I'm back to using the regular tape measure, and we need to move this back about an inch or so, maybe just a little bit forward. Right there looks pretty good at 32. And then we're going to get that same measurement on the other side. With both of our cross bars and towers in place, it's time to move on to our fit kit for our clamps. So we'll open up that security door first. We need to slide this clamp up underneath this bolt here. And now we have a couple of different settings that we can change. First is going to be up and down, and we just want to rotate this until we see that this is lined up to be flush on our roof. And now we will insert the tool into the bolt itself and start tightening that up. In this case, I'm only gonna go to about 50% on this side, and then I'm going to go back to the other side, get that to about 75% and then come back and finish them both, just so I don't pull too much one way or the other. I went back to the other side and now I'm back on the side that we started at to finish up. So I'm gonna tighten it down the rest of the way. Again, waiting until I hear that click sound so I know that it's torqued properly. I'll close the security door up and then we're gonna repeat this process for the rear cross bars, it's gonna be the exact same. The clamps are the same as the front, so you don't need to worry about which ones belong to which. With all our clamps in place we're going to put our end caps on, starting with the bottom, and then we'll click the top into place. And if you opted for the metal lock cores, now you would lock those up. In our case, I'm just going to put our end caps on for now. Once we have all our end caps on and locked up, if you've chosen to do so, I like to finish things out just by doing a shake test to make sure that everything is sturdy and secure. You can see I'm moving the whole vehicle and nothing is moving on here at all. So everything is in place, it's secure, and we're ready to hit the road. Overall, if you're looking for a really rugged, robust and adjustable roof rack system, the Yakima JetStream is going to be a really solid option. I do like that we have those adjustments able to be made to accommodate different roof shapes. In our case, it helped get that front crossbar tapered backwards to make a really flat surface, and I think that overall it matches the aesthetic of the F-150 really well. That being said, all those adjustments might not be for everybody. So if that's the case for you, you can check out the Rhino-Rack Vortex Arrow system. We have videos and a page explaining how that works on this vehicle as well. So feel free to check that out if you want to. A little bit easier to install but less adjustable. So it's kind of either way, whichever way you decide to go though, again, I do think the Yakima JetStream is a really nice option. This, again, was just a quick look at how it fits and how to install it on our 2021 Ford F-150.
Average Customer Rating: 4.8 out of 5 stars (18 Customer Reviews)
This aerodynamic, flush-mount roof rack lets you carry gear and cargo on your vehicle while maintaining a clean, factory look. Crossbars work with channel-mount and clamp-on accessories. Installs on your vehicle's naked roof.Baseclips were as described and shipping was spot on!
Once I got the correct Yakima part numbers they worked very well. I am very pleased!!
Clips were a perfect fit on my 2022 F150
Great service - great price
Works great on my F150 supercrew Lariat
The product was great but having to call and place a second order to get all the parts that were required for installation was not ideal. I used your chat feature for a recommendation as to the product I needed and still didn't get what was required for installation.
Thank you’ll for all your help in getting me the right products I needed.
Very helpful and quick service and delivery.
Great product
Fast service - Very informative about my order.
I purchased clips that were stated as being compatible with our 2010 Chevrolet Impala. The front clips fit well, however the rear clips do not.
From start to finish, the folks at etrailer -- and I spoke to several people there, so it was a consistent corporate vibe -- were fantastic to deal with.
There were delays in getting my product that were on the supplier side and out of eTrailer's control, yet etrailer folks kept me up to date and also worked on a customized solution.
My goal was to be able to carry my surfboard on the roof of our 2019 Hyundai Santa Fe to the beach more than 3 hours away. But the particular model we had had no existing racks, no recessed areas, nothing to fix racks to. Not even the dealer had a solution. I was sh*t out of luck.
But etrailer hooked me up. The racks did take me a while to put on, but most of that time was fine tuning to reduce “hum” while driving. I’m very happy with them.
Thanks to etrailer, I have gone surfing and can go surfing whenever I'd like to.
Had two different vehicles to get ready for two different trips and Joshua diligently tracked dow the correct Yakima accessories and backorder challenges. No other provider came close to this level of service. Excellent work! Both trips made better!
I purchased clips that were stated as being compatible with our 2010 Chevrolet Impala. The front clips fit well, however the rear clips do not.
I have a 10th gen Civic sedan and I was dying to get the perfect roof rack set for my car. At the time of my purchase there was not many visuals of what the rack system looked like on this car.
I purchased the:
•Yakima 50in Jetstream crossbars
•Yakima baseline towers
•bc182 & bc183 clips
•Yakima 46in fairing
Overall I love how it looks on my car! During This COVID pandemic I have been camping more, and this is the perfect foundation! First off, the 46in fairing is the perfect fit for the 10th gen civic! Wind noise is low also with the help of the aerodynamic crossbars. My main concern was the fuel efficiency. On long road trips I still average 38-40 mpg with the rack on. My daily commutes I average 34 mpg without Econ on.
Love my Yakima roof rack!! It exceeds my expectations.great product. Also thank etrailer for the tec support! great staff always there to help thanks again!!
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.