Fork or rear dropout-style mount wash and work stand holds a bike of nearly any size or style. Adjustable-height clamp rotates 360 degrees to hold bike at any angle. Folds up for compact storage.
Features:
Specs:
This lightweight, wash and work stand lets you perform on-the-go maintenance on your bike. It's a great stand for carbon bikes since it makes no contact with your bike's frame. It has a fork mount that grips your bike by the front or rear dropout. The fork mount slides along the beam to accommodate most bike sizes and styles and it accepts most axle configurations. Quick-release collars let you easily raise and lower your bike and rotate it 360 degrees. It also has a wide, 3-legged base with rubber-coated feet for stability on nearly any surface.
The Sprint lets you mount your bike to the beam by its front or rear dropout. The fork mount keeps your handlebars and wheel facing forward while you work so you don't need a special holder required for clamp-on work stands. The fork block is setup to accommodate 15-mm thru-axles, standard quick-release axles, and 12-mm x 142-mm thru-axles. You will need an adapter (sold separately) to mount other quick-release and thru-axles. To swap adapters simply unscrew the large, threaded barrel from the fork block, insert the new adapter, and screw the barrel back in.
To mount your bike set the bottom bracket on the rubber support pad. Adjust the placement of the fork block by loosening the knob and sliding it across the beam until it's flush with your fork. You can also mount your rear dropout to the fork block, leaving your front wheel elevated off the stand. If you mount your bike this way you may need the Flop Stop handlebar holder (sold separately) to keep your handlebars and wheel facing forward.
You can rotate your bike 360-degrees for quick access to any part of your bike without moving the stand. Simply pull the lever to loosen the upper quick-release collar and clamp it back down to lock your bike in place.
The telescoping tube lets you raise and lower the beam. Simply loosen the lower quick-release collar, set your bike to the desired height, and re-tighten the collar.
The boom arm clamps to the stand with a spring-loaded quick-release lever. To set it up you must raise the bolt head slightly so that it aligns with the boom arm, then clamp it in place.
The stand can be folded up for compact storage in your vehicle, garage, or Feedback Sports tote bag (sold separately). Simply loosen the knob, fold the feet in, and tighten the knob to secure it into position.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to be taking a look at Feedback Sports Sprint Bike Work Stand, Part Number 301-16690. Beam style work stands are ideal for anyone who can't clamp to their bike's frame or seat post, such as tri-bikes or all carbon fiber bikes. It's going to work with your standard nine millimeter road bike or mountain bike axles. It will also work with your 15 millimeter thru-axles. For 20 millimeter through-axles, you can pick up an adaptor with Part Number 301-16751. It's adjustable 360 degrees. As I spin it around, you can see the bottom bracket pad.
This is going to safely support our bike without damaging it. With the way the bottom bracket supports our bike, we can still perform maintenance to our crank set. We've gone ahead and removed our bike, so we can take a closer look. The fork block itself is adjustable along the beam to accommodate different wheel bases. Once we've got it set, we can tighten it up. The work height is adjustable from 30 inches up to 48 inches.
Once we've got it set, we'll close up our lever. Then we can just slide down our free collar to lock it in place. It has a base diameter 46 inches and a weight capacity of 85 pounds. It's made out of an aluminum construction, so it's going to be lightweight and resist rust and corrosion. When not in use, the whole thing collapses for compact storage. We'll start with our lever underneath our beam.
We'll loosen it up. We'll pull it all the way to the bottom bracket, then fold it down. Then we'll raise up our legs. We'll pull out the lever here, guide it up, until they're completely closed. Then finally, we'll lower it down.
With it in this position, it's easy to store or travel with or you can pick up the Feedback Tote Bag with Part Number 301-16675. If you'd like to pick up a tool tray for your work stand, that's Part Number 301-15659. That's going to complete our look at the Feedback Sports Sprint Bike Work Stand, Part Number 301-16690.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.