Replacement Relay Switch for Bulldog Winch Air Compressor - 40 Amp
(2 reviews)
Price: $8.50
In Stock
Replacement Relay Switch for Bulldog Winch Air Compressor - 40 Amp
Item # BDW42035
Retail:$9.06
Our Price: $8.50
You Save: 6%
In Stock
Need help with installation?
Locate installers near me- All Info
- Reviews (2)
- Q & A (0)
- Videos (1)
- Photos
Bulldog Winch Accessories and Parts - BDW42035
- Air Suspension Compressor Kit
- Vehicle Suspension
- Relays
- Bulldog Winch
Replaces the 40-amp relay switch in your Bulldog Winch air compressor. It opens and closes the high-amp circuit to your Bulldog Winch compressor. 4-Post, Bosch-style relay.
Features:
- Replaces the 4-post, Bosch-style 40-amp relay switch in your air compressor
- Mounting tab molded into relay case
Specs:
- Dimensions: 2" long x 1" wide x 1" deep
- 1-Year limited warranty
42035 Replacement Relay Switch for Bulldog Winch Air Compressor - 40 Amp
California residents: click here
Video of Replacement Relay Switch for Bulldog Winch Air Compressor - 40 Amp
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of Bulldog Winch Air Compressor Parts - 60 Am Relay - BDW42035
Today we'll be taking a look at the replacement relay switch for Bulldog Winch air compressor. This is going to keep your compressor working properly and prevent any issues with overloading or overheating. The switch is going to open and close the high amp circuit to your Bulldog Winch compressor. It's a four-post Bosch style relay. It has a mounting tab at the back that's molded into the relay case, so you don't have to worry about finding a place to mount this up; you can use a self-tapping screw to attach that securely. It has a little bit of a guide there, as far as what post goes where.
They're numbered out; it's a little hard to see on camera, but it does have that printed on there to make it a little bit easier to install. It is a 60-amp relay; works with 12-volt systems.As far as dimensions, it's about 1 1/4" wide with that tab at the back, and then about 1" long. From the top of the tab to the end of our posts, it's about 2 1/8". Bulldog Winch gives us a one-year, limited warranty. That's going to do it for our look at the replacement relay switch for Bulldog Winch air compressor.
If you need any other accessories for your Bulldog Winch air compressor, you can always check out etrailer.com for any of those needs..
Customer Reviews
Replacement Relay Switch for Bulldog Winch Air Compressor - 40 Amp - BDW42035
Average Customer Rating: 4.0 out of 5 stars (2 Customer Reviews)
Replaces the 40-amp relay switch in your Bulldog Winch air compressor. It opens and closes the high-amp circuit to your Bulldog Winch compressor. 4-Post, Bosch-style relay.by: Bob01/07/2021
Products as ordered. Delivery a little slow.
by: Richard 11/10/2022
2
2
See what our Experts say about this Bulldog Winch Accessories and Parts
- How To Troubleshoot a Relay Which Has Power Going In But Not Coming OutBe sure to check the connectors on your Relay # BDW42035 as to ensure everything is properly connected. On this particular relay the #85 connector is the input for battery power which goes to the switch on the #86 connector. This will activate the #87 terminal which gets power from the #30 terminal. Be sure to verify you are getting power to the switch side of the relay and the switch for the relay is not damaged. If there is no power on the switch side the relay will need replaced. Please...
view full answer... - How To Prevent Tekonsha Primus Trailer Brake Controller From Draining Vehicle Battery When Sitting I wish I could give you an exact power draw for the Tekonsha Primus IQ Trailer Brake Controller # TK90160 but after spending 2 hours on hold with them they only said it is near 0 draw. Since it sounds like your Primus is connected directly to the battery and not a ignition powered switch you might consider adding a Relay # BDW42035 so the power going to the controller will switch off when the ignition is switched off. With any battery which sits for months at a time you really should...
view full answer... - Connecting Relay To 7-Way Charge Line Circuit To Prevent Trailer Draining Vehicle Battery While OffTo only send power to the 12 volt charge line circuit on your 2001 Chevrolet Suburban you need to add a Relay Switch # BDW42035. With this switch you will be able to connect it to an ignition circuit wire that only receives power when the ignition switch is placed in the run position. You will need to find where the 12 volt charge line is getting its power from the battery and connect the relay in line. There are 4 connections on the Relay. #30 Fused Battery Connection #85 Ground Terminal #86...
view full answer... - Parts Needed To Use Curt Echo Trailer Brake Controller On a 2008 Toyota Tacoma With T-One 118496As you already have the T-One Vehicle Wiring Harness # 118496 on your 2008 Toyota Tacoma you will want to use the 7-Way RV Upgrade Kit # ETBC7L. This will give you the 7-way you need to plug the Curt Echo # C51180 into. It also includes the wiring and circuit breaker needed to connect to your battery. This will connect directly to the battery unless you wish to connect it to the ignition with a Relay # BDW42035. This will then only provide power to the charge line when the ignition is switched...
view full answer... - Parts Needed To Replace Factory Brake Controller Wiring On a 2012 Chevrolet Silverado 3500 Flat BedIf the issue is with the wire running to the 7-way you will only need 10 gauge Wire # 10-1-1 to run from the brake controller to the 7-way. You will just cut out the factory connection and install this wire using 2 of the Butt Connectors # DW05745-5. If they are concerned about the power and ground wires you will simply need to run new wire with a Circuit Breaker # 9510 to the battery for power. If they do not want power always on for the brake controller you will also need to wire in a...
view full answer... - Troubleshooting Trailer Charge Line Draining Battery On 2020 Ram 2500 When Ignition Is Switched OffYou will want to contact your local Ram dealer to determine if there is a ECU Flash which will fix the issue of the charge line sending power when the ignition is switched off. I do know this was an issue with older Ram trucks and the only way to resolve this was by installing a Relay # BDW42035 in line of the charge line. This will allow you to connect the switched side of the relay to an ignition source so power only flows through the charge line with the ignition switched on.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Edited by:
Tyler C
Video Edited:
Kathleen M
Written by:
Matthew S
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.