Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…
The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Mitsubishi Expo AccessoriesSelect A Category Below
Towing
Mitsubishi Expo Trailer Wiring
Mitsubishi Expo Brake Controller
Mitsubishi Expo Base Plate for Tow Bar
Mitsubishi Expo Vehicle Tow Bar Brake System
Mitsubishi Expo Vehicle Tow Bar Wiring
Cargo Control
Mitsubishi Expo Roof Rack
Mitsubishi Expo Trunk Bike Rack
Performance Accessories
Mitsubishi Expo Air Filter
Mitsubishi Expo Suspension Enhancement
Mitsubishi Expo Transmission Cooler
Mitsubishi Expo Vehicle Lights
Mitsubishi Expo Tire Chains
Mitsubishi Expo Fluid Filters
Mitsubishi Expo Catalytic Converters
Mitsubishi Expo Vehicle Engine Heaters
Mitsubishi Expo Radiator Fan
Vehicle Trim
Mitsubishi Expo Floor Mats
Mitsubishi Expo Vehicle Covers
Mitsubishi Expo Windshield Wiper Blades
Mitsubishi Expo Windshield Covers
Mitsubishi Expo Vehicle Air Mattress