Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that.…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do…
Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…
The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Mazda Protege AccessoriesSelect A Category Below
Towing
Mazda Protege Trailer Wiring
Mazda Protege Brake Controller
Mazda Protege Base Plate for Tow Bar
Mazda Protege Vehicle Tow Bar Brake System
Mazda Protege Vehicle Tow Bar Wiring
Cargo Control
Mazda Protege Roof Rack
Mazda Protege Trunk Bike Rack
Performance Accessories
Mazda Protege Air Filter
Mazda Protege Transmission Cooler
Mazda Protege Performance Chip Tuners
Mazda Protege Vehicle Lights
Mazda Protege Tire Chains
Mazda Protege Fluid Filters
Mazda Protege Catalytic Converters
Mazda Protege Vehicle Engine Heaters
Mazda Protege Radiator Fan
Vehicle Trim
Mazda Protege Floor Mats
Mazda Protege Vehicle Covers
Mazda Protege Side Window Vents
Mazda Protege Vehicle Seat Covers
Mazda Protege Replacement Mirrors
Mazda Protege Windshield Wiper Blades
Mazda Protege Windshield Covers
Mazda Protege Vehicle Air Mattress