Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…
The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Isuzu VehiCROSS AccessoriesSelect A Category Below
Towing
Isuzu VehiCROSS Trailer Wiring
Isuzu VehiCROSS Brake Controller
Cargo Control
Isuzu VehiCROSS Roof Rack
Performance Accessories
Isuzu VehiCROSS Air Filter
Isuzu VehiCROSS Suspension Enhancement
Isuzu VehiCROSS Transmission Cooler
Isuzu VehiCROSS Performance Chip Tuners
Isuzu VehiCROSS Vehicle Lights
Isuzu VehiCROSS Tire Chains
Isuzu VehiCROSS Fluid Filters
Isuzu VehiCROSS Salt Spreader
Isuzu VehiCROSS Vehicle Engine Heaters
Isuzu VehiCROSS Radiator Fan
Vehicle Trim
Isuzu VehiCROSS Floor Mats
Isuzu VehiCROSS Vehicle Covers
Isuzu VehiCROSS Side Window Vents
Isuzu VehiCROSS Windshield Wiper Blades
Isuzu VehiCROSS Windshield Covers
Isuzu VehiCROSS Vehicle Air Mattress