Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I&…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…
The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Honda Accord AccessoriesSelect A Category Below
Towing
Honda Accord Trailer Hitch
Honda Accord Trailer Wiring
Honda Accord Brake Controller
Honda Accord Base Plate for Tow Bar
Honda Accord Vehicle Tow Bar Brake System
Honda Accord Vehicle Tow Bar Wiring
Cargo Control
Honda Accord Roof Rack
Honda Accord Trunk Bike Rack
Performance Accessories
Honda Accord Air Filter
Honda Accord Exhaust
Honda Accord Transmission Cooler
Honda Accord Performance Chip Tuners
Honda Accord Vehicle Lights
Honda Accord Tire Chains
Honda Accord Fluid Filters
Honda Accord Catalytic Converters
Honda Accord Vehicle Engine Heaters
Honda Accord Radiator Fan
Honda Accord Cabin Air Filter
Honda Accord Lift Assist
Vehicle Trim
Honda Accord Floor Mats
Honda Accord Trim Kits
Honda Accord Vehicle Covers
Honda Accord Bug Shield
Honda Accord Side Window Vents
Honda Accord Vehicle Seat Covers
Honda Accord Replacement Mirrors
Honda Accord Windshield Wiper Blades
Honda Accord Windshield Covers
Honda Accord Vehicle Air Mattress