Customers compare EM34416 to these similar products
Products Featured in this Video
What's up everybody, it's Aj with etrailer.com. Today we'll be checking out this retractable ratchet strap from Ericsson. It also is a push button to recall. So let me show you what I'm talking about. You pull it out like that and hit this red button. And it goes back in like that.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
For your Adarac Custom Truck Bed Ladder Rack, like the Steel #A70490, that you have installed on your Ford F-150, I recommend using the Thule Hull-A-Port Kayak Carrier #TH834. The Adarac crossbars on the systems we have available for your truck…
view full answer...The Draw-Tite Front Mount Trailer Hitch Receiver #DT44HR is confirmed to fit your 2021 GMC Sierra 1500 with the 3.0L diesel engine. This receiver is rated for a vertical load up to 500lbs and a line pull rating of up to 9,000lbs. This Draw-Tite…
view full answer...I would be happy to help. Since you have identified that the issue is on your 2019 Chevrolet Silverado 1500 since the trailer works when you connect it to other trucks, I would first check your trucks connector for any debris or corrosion that could…
view full answer...Yes, trailer running lights and parking lights are the same circuit. So on a vehicle when you turn the headlights on there's the position on the selector right before you get to the headlights where all of the exterior lights of the vehicle come…
view full answer...This will depend on the hitch used and the height of the trailer coupler. You want the trailer to be as level as possible. We have a page on calculating hitch height and coupler height to help you find what ball mount would work best. Most light duty…
view full answer...I reached out to my contact at ShockStrap and the ShockStrap Ratchet Tie-Down Straps w Shock Absorbers - 1-1/2" x 7' - 1,000 lbs - Qty 2 #297-7RSDB has a minimum length of 29". Now this will work just fine at 32" that you were…
view full answer...In almost all cases the limiting factor for tire pressure on a wheel setup is the valve stem. If you upgrade the valve stem in your wheels to ones that can handle 110 psi like what the part #AM10501 calls for you'd be fine. Usually valve stems…
view full answer...To secure your Hobie Mirage Pro Angler 14 with 360 Drive Technology to the lower level of the Yakima EasyRider Double Decker Trailer #Y08129 I recommend the Yakima BigCatch Kayak Carrier #Y04091. The BigCatch is confirmed to fit the lower round bars,…
view full answer...When choosing a jack for your trailer you will want to remember that the jack is not going to be lifting the entire weight of the trailer. You should choose a jack that exceeds the tongue weight of your trailer when it is fully loaded. The tongue…
view full answer...If you're looking for the hard plastic piece that covers the manual override on your Lippert Smart Jack Electric Trailer Jack #LC643589, you can use part #LC733925. Aside from that and the drop leg #LC405217, Lippert does not offer any other…
view full answer...Two 12 foot long bunks boards will work well to support your 21 foot boat. Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like. Due to shipping…
view full answer...There certainly wouldn't be any negative effects from using two self-centering keel rollers like the CE Smith Keel Roller part #CE29505 although some might say it's redundant.
view full answer...