Customers compare STL69RRXB to these similar products
Products Featured in this Video
Today we're going to review part number STL69RRXB. This is the Optronics Sealed Thin Line over 80-inch trailer LED stop turn taillight. This is a 3-function 11-diode red reflector. This red rectangular trailer light will serve 3 functions for trailers that are more than 80-inches wide. It'll be the stop, the turn and the taillight. It does include an integrated reflector to fulfill the rear reflex… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack…
view full answer...According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement…
view full answer...We have toppers that'll work for 2 of your 3 sliders. For your 12 foot 9-1/2 slide, use #LCV000168109 which is designed for slides measuring between 152-157 inches wide. The longest topper we offer is for slides 188-193-3/4 inches, so…
view full answer...I recommend to use the Solera 16-1/2' Slider part #LCV000435661 which matches the boxes width exactly so you will not have side overhang like we normally recommend but it is the biggest slide topper available to fit the 198" width of your…
view full answer...Please note the attached instructions. The Lippert Anti-Billowing Kit for Solera Slide Topper Awnings, #LC78FR should be installed on the end of the awning that is closest to the front of the unit. 1. Make sure awning is fully retracted. 2. Place the…
view full answer...Yes, the 7-way to 5-way and 4-way Adapter, #C35FR, will work with your 2005 Land Rover LR3 as long as your factory 7-way trailer connector. This adapter was originally designed for certain European vehicles with incandescent tail lights and factory…
view full answer...I checked the owner's manual for your 2021 GMC Yukon XL, and yes, it is perfectly fine to flat tow. That being said, you are going to need these components: - A base plate - Tow bars - Braking system - Tow bar wiring - High-Low adapter For a base…
view full answer...I advise measuring the two spindles that you have and making sure that the parts that you are wanting to interchange will be a compatible fit. I have included a photo that shows where where to take these measurements on your exiting spindles. These…
view full answer...Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 referenced in your question do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life…
view full answer...According to Solara (Lippert), the correct number of turns to set the proper tension of their slide toppers like #LCV000163285 is between 12 to 16 turns, so I'd consider 14 to be a pretty good happy medium.
view full answer...My contact at Redline told me that the outside diameter of the Chrome Trim #SA1012ET would be right at 5/16 of an inch and the inner diameter 1/8 of an inch. He said the trim isn't a perfect circle so the dimensions fluctuate a little bit.…
view full answer...Sounds like you need to redo the wiring of the new 4-way completely. Typically, the green wire runs to the right turn/stop circuit, the yellow runs to the left turn/stop circuit, the brown wire runs to the taillights and the white is the ground that…
view full answer...