Customers compare BWTS30049B to these similar products
Products Featured in this Video
Speaker 1: Today we're taking a look at the B&W Tow and Stow 3 inch ball mount for three inch hitches. This ball mount with the built in hitch balls lets you hook up your trailer to your tow vehicle. The shank slides into the receive tube of your hitch, and then the hitch balls provide the connection points for the trailer coupler.It can be used in either the drop or rise positions, and… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The B&W Tow & Stow 3-Ball Mount #BWTS10049B is rated for 10,000-lbs when you use the highest-capacity ball, the 2-5/16-inch size. This equates to a Class IV rating. When the other smaller hitch ball sizes are used the weight ratings…
view full answer...The newer Chevrolet and GM pickup trucks have a known power deficiency issue with the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras #FCE48TASL-05. There is likely nothing wrong that you did, the problem is the…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...For your Super Titan 3000 Weld-On Trailer Hitch with 3" Receiver #38023 I recommend using the Curt Hitch Receiver Reducer Sleeves #C45408. These sleeves can both be used at the same time to reduce your 3" receiver to a 2"…
view full answer...For your 2017 Ram 2500 that has the factory 3 inch hitch we have a couple B and W Tow n Stow adjustable ball mount options available. We have the part #BWTS30037B which can do a drop of up to 4-1/2 inches and we have the part #BWTS30040B which can do…
view full answer...The Curt Rebellion XC cushioned ball mount part #C83WR would cushion the ride quality and reduce the movement you are experiencing but an easier and most cost effective solution would be an anti-rattle device like the etrailer #e99007 which will lock…
view full answer...The SureCall Fusion2Go Max Cell Phone Signal Booster for Cars and Trucks #SC53MR is not limited to just inside the vehicle. That being said, the signal booster range is more limited (a few feet from the antenna). If you are directly outside the…
view full answer...There is one lock set I really like the most that is going to give you the best overall protection for the 15,000 lb capacity Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2" and 2-5/16" Balls #C83WR: - InfiniteRule Lock Set…
view full answer...The Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2" and 2-5/16" Balls #C83WR is 8" from the bottom of the receiver shank to the bottom of the adjustable mount.
view full answer...I reached out to Curt who stated at this time the cushioning material inside the Rebellion XD Shock Absorbing Adjustable Ball Mount #C83WR is not replaceable. They have tested the Rebellion to having more than 1 million cycles and the cushioning did…
view full answer...The Curt Rebellion XD Shock Absorbing Adjustable Ball Mount part #C83WR won't work with a weight distribution system due to the design of the adjustable shank but we do have a very similar option that will, the Gen-Y Torsion Weight Distribution…
view full answer...You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
view full answer...