Install Kit to Use Draw-Tite 5th Wheel Hitch 6033 in a 2011 GMC Sierra 2500 Short Bed

Question

Question:

Will a Draw Tite 6033 hitch work on my 2011 gmc 2500 short bed

asked by: Jack S

0

Expert Reply:

Yes, the now discontinued Draw-Tite 5th wheel slider hitch 6033 can be used in your 2011 GMC Sierra 2500 short bed. You will just need an installation kit for the truck.

You have some options for an installation kit. You can use a universal kit, # RP30035. The benefit is the lower cost. But this kit does require drilling into the truck frame and will take longer to install compared to a custom kit.

For a custom kit you can use # RP50066-58. The cost is higher but there is no drilling of the truck frame required and it will install in less time than the universal kit. I have linked a video and the instructions to the right for the custom kit and the instructions for the universal kit for you to check out.

expert reply by: Michael H

0

Answer 1

Yes, your Reese 5th Wheel Hitch will work with the B&W Custom Installation Kit w/ Base Rails part #BWRVK2604 which is a fit for a 2019 Ram 1500 with the 6-1/2' bed. If you have a Reese Sidewinder, you can reuse this with your Reese 5th Wheel…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Install Kit to Use Draw-Tite 5th Wheel Hitch 6033 in a 2011 GMC Sierra 2500 Short Bed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching