Installation Methods for Brophy Recessed Trailer D-Ring Tie Down with Backing Plate # RR5K
Question:
I notice there are different suggestions between the two videos on how to install the Brophy recessed D ring in the wood flooring of a trailer. One video says to use a 3.5inch drill the hole and go down 5/8inch to accommodate the body of the D-ring. The second video that shows its use in a covered trailer shows the installer drilling the same hole clear through the board. Is one better than the other? One stronger than the other?
asked by: Jerry
Expert Reply:
The Brophy Recessed Trailer D-Ring Tie Down with Backing Plate # RR5K is not application-specific so its preferred method of installation will vary from trailer to trailer. The main factor is the thickness of the material to which it will be mounted. All other things being equal, the installation that only removes the minimum amount of material necessary for clearance under the tie down plate will leave the original surface somewhat stronger than if all of that material were removed. In all likelihood the D-ring assembly, rated at 5000-lbs, will exceed the strength of the material to which it is mounted on most trailers.
Product Page this Question was Asked From
Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Tie Down Anchors
- Trailer Tie-Down Anchors
- Truck Tie-Down Anchors
- Tie-Down Cleats and Rings
- 1600 lbs
- D-Ring
- Surface Mount - Bolt-On
- Brophy
more information >
Continue Researching
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Q&A: Is 3/4 Inch Plywood Floor Adequate for D-Ring Tie Down Anchors with Backing Plate for 3,000 lb Car
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Shop: Trailer Axle w/ Electric Brakes - Easy Grease - 5 on 4-1/2 Bolt Pattern - 95" Long - 3,500 lbs
- Shop: Brophy Swiveling D-Ring Anchors w Backing Plates and Hardware - Bolt-On - 2,000 lbs - Qty 4
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Backing Plate for Tandem Axle Trailer Fender - Steel - 69" x 12"
- Video: Dexter Axle Trailer Brakes - Electric Drum Brakes - 23-26-27 Review
- Q&A: Can Erickson E-Track Be Used on Exposed Deck of Open Utility Trailer
- Video: Review of etrailer Trailer Fenders - Tandem Axle Trailer Fenders - HP94VR
- Video: Review of etrailer Trailer Fenders - Tandem Axle Steel Fenders - HP22FR
- Video: Review of etrailer Trailer Fenders - Tandem Axle - HP64VR
- Video: Review of etrailer Trailer Fenders - Rectangular Backing Plate - HP72FR
- Q&A: What is the Best Size Wire Loom for Bonded 4 Wire and One 12 Gauge Wire
- Video: Review of Dexter Trailer Hubs and Drums - Pre-Greased 3500 LB - 84546UC3-EZ
- Video: Dexter Electric Trailer Brake Kit Installation 23-26
- Shop: Transmission Cooler
- Shop: Suspension Enhancement
- Q&A: Inner Dimensions of Commercial Grade Battery Box for Group 4D Batteries # 329-HM408
- Q&A: How To Install The Brophy Trailer D-Ring Tie Down, # RR5K, On A Wood Trailer Floor
- Search Results: rr5k
- Search Results: tow tax
- Search Results: tow rax
- Search Results: brophy d rings
- Q&A: Determining Which Size Screws Should Be Used To Install Tow-Rax Strap Hanger TWSP25SHA
- Q&A: What Diameter Hole Needs to be Cut for the Brophy D-Ring Recessed Tie Down
- Shop: Trailer Hitch
- Search Results: e track
- Search Results: tire covers