Diameter of the Square Portion of the Carriage Bolt M6-1 x 75mm # TH10403

Question

Question:

Im looking at using these for a very specific application. What are the exact measurements width specifically of the square portion of the carriage end of the bolt? Measurement V in the attached image. Thanks in advance,

asked by: Shane

0

Expert Reply:

I went out and pulled a Carriage Bolt M6-1 x 75mm # TH10403 from our warehouse to measure the square portion of the bolt and found that it measures .31 of an inch.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went and pulled a #THXADAPT9 from our warehouse to get the dimensions you asked for and the square holes are 1/4 inch by 1/4 inch and are 4 inches apart on center. This only includes one bracket.

view full answer...

Answer 2

Correct, the Replacement Plate Box Support part #TH10378 which is a direct replacement for the Thule Weekender 627 will install directly beneath the cargo box which you can see in the attached photo. The plates are designed to prevent the mounting…

view full answer...

Answer 3

The Carriage Bolt M6-1 x 75mm #TH10403 comes with 1 bolt. Yes, the price listed is the cost for 1 bolt.

view full answer...

Answer 4

You likely should go ahead and fully replace the mounting hardware. Unfortunately, there isn't a kit available anymore for the Weekender, but all of the individual parts are available. I've listed them out with their part numbers and the…

view full answer...

Answer 5

The carriage bolts used for the Thule Summit cargo box are #TH10403, sold in quantities of 1. The knob is #TH04877, also sold in quantities of 1. If you need all of the bolts and knobs then you will need 8 of each.

view full answer...

Answer 6

For your Thule Summit Cargo Box, the correct mounting hardware kit is the QM3 Quick Mount Hardware #TH04997. This kit includes all of the needed mounting hardware to attach the Thule Summit to the crossbars on your vehicle's roof. We do also have…

view full answer...

Answer 7

Yes, you can get the pads, bolt, and wing grip separately from the QM3 - Quick Mount Hardware #TH04997 with the following part numbers: Protector Pads - #TH05001 Carriage Bolt - #TH10403 Wingnut - #TH04877

view full answer...

Answer 8

The closest thing we offer to what you are looking for is the Replacement Carriage Bolt #TH915-0675-11 which is a M6 Carriage bolt that is 75mm.

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Diameter of the Square Portion of the Carriage Bolt M6-1 x 75mm # TH10403

Product Page this Question was Asked From

Continue Researching