Which Wire Goes Where on a Reverse Lockout Solenoid

Question

Question:

Need to know how to wire the solenoid. On my old actuator, the solenoid only had 1 wire. The new one has 2, Im assuming 1 is ground but they are both yellow wires?

asked by: Garret

0

Expert Reply:

It doesn't matter which wire is used for the power circuit and which is ground. Either wire will do fine. Run one of the wires to your reverse light circuit and then ground the other circuit and you will be good.

expert reply by: Jameson C

0

Answer 1

The channel on the Demco Hydraulic Brake Actuator w/ Electric Lockout - Disc - Primed - Adjustable Channel - 8,000 lbs #DM8759422 you were looking at is 2-15/16" wide, 8" long, and the holes are 2" apart center to center as…

view full answer...

Answer 2

I spoke with my contact at Titan about the issue you are having with the Titan Zinc-Plated Brake Actuator w/ Electric Lockout - Disc - 2-5/16 inch Ball - 8,000 lbs, part #T4747220, on your trailer. He informed me that there is no pressure…

view full answer...

Answer 3

You gave quite a few options, but the Demco Solenoid Kit - Factory Installed - Disc Brakes #DM5752 sill be the best option as you stated. You can reuse your other parts as you stated. This assembly will have the spring and piston as you stated. If…

view full answer...

Answer 4

I went out to the warehouse and measured the bolt holes on actuator #T4747220. The 2 larger holes are spaced 5 inches apart on center. I have included a picture showing this and other measurements for you.

view full answer...

Answer 5

The distance from the forward most mounting hole of the Titan Zinc-Plated Brake Actuator w/ Electric Lockout #T4747220 that you referenced to the very end of the solenoid shield is 18 inches.

view full answer...

Answer 6

The bolt hole dimensions of the Demco Brake Actuator #DM8669112 are 12-1/2 inches on center and 3 inches on center. I've attached a photo to assist. The Titan #T4747220 has mounting holes that are 3 inch on center so 2 of the 3 holes will…

view full answer...

Answer 7

I attached a picture that shows all of the mounting hole dimensions pointed out as well as a second picture that shows the distance from the front mounting hole to rear of shroud on the Demco DA91 #DM8750311 you referenced.

view full answer...

Answer 8

The Demco Hydraulic Brake Actuator w/ Drop and Electric Lockout - Disc - Zinc - 2-5/16" Ball - 8K #DM8750311 has 5 holes for adjustability and fit with the majority of couplers. The weight rating is based on utilizing all of the bolt holes…

view full answer...

Answer 9

Attached is a portion of the instructions for the Demco Hydraulic Brake Actuator #DM8759422 that gives the details on how to bleed the brakes of your trailer. You will need to use a brake bleeder like part #ALL648591 to perform this. The…

view full answer...

Answer 10

On the Pro Series Adjustable-Channel Coupler, #PSA256S0303, the back of the coupler that fits in the channel mounted to the trailer measures 2-7/8 inches wide. The bolt holes are 2 inches apart on center. Mounting hardware is included with this…

view full answer...

Answer 11

The Pro Series brand gives you an incredible value when compared to similar product brands. The price for the Pro Series Adjustable-Channel Coupler w/ Low Latch #PSA256S0303 is accurate. You will notice that most of the more expensive products…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Which Wire Goes Where on a Reverse Lockout Solenoid

Product Page this Question was Asked From

Continue Researching