Installing Trailer Wiring Harness on a 2014 Honda Odyssey Elite with HondaVac Vacuum

Question

Question:

I have a 2014 Honda Odyssey Elite, which has the built-in vacuum cleaner feature. Your video doesnt match what I have on the drivers side. Will the installation be the same, or will it require an alternate installation procedure? Thanks.

asked by: Mike R

0

Expert Reply:

In order to install the trailer wiring harness # 118521 on your 2014 Honda Odyssey with the built-in vacuum you would have to remove the vacuum, 12 volt power plug, and subwoofer in order to then follow the installation instructions. A trim panel remover tool, # PT73HJ, would be helpful to get the panels loose.

expert reply by: Michael H

0

Answer 1

For a 4-pole flat type wiring harness to go along with the hitch on your 2016 Honda Odyssey SE you can use the Tow Ready #118521. This is a custom-fit powered taillight converter that will protect your Odyssey's wiring from any faults or shorts…

view full answer...

Answer 2

Hi! I checked with Curt and the T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56378 will work with all models of the 2016 Honda Odyssey - the EX, LX, EX-L, SE, Touring and Touring Elite so you are good to go. If you need a…

view full answer...

Answer 3

All of the hitches offered for the 2016 Honda Odyssey Touring Elite, shown on the linked page, will install as close to the bottom of the bumper cover as possible. The Odyssey and similar vehicles like the Toyota Sienna have a low-slung rear end…

view full answer...

Answer 4

Although Tow Ready hasn't done an install on an Odyssey that's equipped with the HondaVac option, I was able to obtain some very welcome feedback from one of our Customers who recently installed the #118521 on his 2015 Odyssey SE with the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...