What Parts are Included with Erickson Hitch Mounted Load Extender

Question

Question:

what is included in with the darby Extended Truck hitch, and what else come witn the hitch ?

asked by: james E

0

Expert Reply:

There are two main pieces, the L shaped piece and the T shaped piece. Both ends of the L fit into the T so that the cross bar can be positioned behind the truck or up higher level with the cab. The pins that hold the extender together are included, but you will need a hitch pin and clip like part # e45TR.

expert reply by: Patrick B

0

Answer 1

The Erickson load extender #EM07605 is a gread extender. I would strongly recommend using an substantial anti-rattle device when using a load extender like this because they do tend to move quite a bit. For an anti-rattle device I recommend #BX88224…

view full answer...

Answer 2

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 3

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The only difference between the #RG06-050 and Timken #TMK58ZR is the brand and quantity. Timken is typically considered to be a high quality brand, particularly for their USA made bearings. The #RG06-050 comes with two seals so it is the better…

view full answer...

Answer 8

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 9

We actually have the Brake Buddy 32220 reverse solenoid available with the Titan Solenoid Valve Replacement Kit #TK71-755-00. The solenoid itself would be an exact replacement and it features the two mounting holes at the bottom like you described…

view full answer...

Answer 10

The Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar #RTL002 does use the Hitch Lock #RRRBCA025.

view full answer...

Answer 11

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

What Parts are Included with Erickson Hitch Mounted Load Extender

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching