LED Lights, Wiring and Mounting Brackets for Reverse Lights On a Boat Trailer
Question:
I need 2 complete LED Clear Lens submersible back up lights to place under the rear bumper. Bright white lighting to assist backing up vehicles that often go underwater to launch boats.
asked by: Charlie
Expert Reply:
I would use the Sealed, 6-1/2 inch LED Clear Oval Trailer Utility Light, 10 Diode, item # BUL72CB, along with the Rubber Grommet for 6-1/2 inch Oval Trailer Tail Lights, item # A70GB, and the Trailer Light Mounting Bracket for 6-1/2 inch Oval Trailer Lights, Steel - Black Powder Coat, item # BK70BB. These items should work for you and have a specific mounting bracket that is not available for the Thinline Sealed LED Utility Light, item # UCL65CB. Be sure to unplug the trailer connection before entering the water.
You will need to wire the lights to the backup light circuit on the vehicle. If you have a factory installed 7-Way connector then the vehicle connector should have the backup circuit connected to the center pole. If not you can wire the center pole on the 7-Way to the reverse light circuit. I would use the 10 Gauge Blue Primary Wire, item # 10-1-1 and a quick splice, item # SWC501915-1. Use a circuit tester, item # 3808 to find the reverse circuit behind one of the tail lights.
If you have a 4-Way at the rear of your vehicle then I would use the 5-Flat Vehicle End 5-foot Wiring Harness, item # HM37908, and the 5-Flat Trailer End 48 inch Harness, item # 20017, to complete the wiring needed for the reverse light circuit.
Products Referenced in This Question
5-Flat Trailer End 48" Harness
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 5 Flat
- Draw-Tite
more information >
PVC Grommet for 6-1/2" Oval Trailer Tail Lights
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- Grommet
- 6-1/2 Inch Long
- Oval
- Optronics
more information >
Trailer Light Mounting Bracket for 6-1/2" Oval Trailer Lights, Steel - Black Powder Coat
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- 6-1/2 Inch Diameter
- Brackets
- Black
- Optronics
more information >
Optronics LED Trailer Utility Light - Submersible - 10 Diodes - Oval - Clear Lens
- Work Lights
- Utility Lights
- Exterior Lights
- Interior Lights
- Oval
- Recessed Mount
- LED Light
- White
- Optronics
more information >
Hopkins Wiring Harness with 5-Pole Flat Trailer Connector - Vehicle End - 5' Long
- Trailer Wiring
- Trailer Connectors
- Vehicle End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 5 Flat
- Hopkins
more information >
Quick Splices - Self-Stripping Connector - Closed Port - 10-12 Gauge - Yellow - Qty 1
- Wiring
- Wire Connectors
- Quick Splice Connectors
- 12-10 Gauge
- Spectro
more information >
Product Page this Question was Asked From
Thinline LED Trailer Utility Light - Submersible - 6 Diodes - Rectangle - Clear Lens
- Work Lights
- Utility Lights
- Exterior Lights
- Rectangle
- Surface Mount
- LED Light
- White
- Optronics
more information >
Continue Researching
- Q&A: Mounting Cover for Tecnic 45 Degree Accent Light
- Article: Trailer Tire Sizing
- Q&A: Replacement Clearance Lights 1-1/4" Tall, 3-15/16" Long and 7/8" Deep With 2 Prong Connectors
- Q&A: What is the Difference Between 7-Way RV and Utility Trailer Connectors
- Q&A: What Gauge Wire Should be Used to Wire 8 Marker Lights, Incandescent or LED
- Q&A: Replacing Trailer 5-Way Connector That has 7 Wires
- Article: Trailer Wiring Diagrams
- Q&A: What is the Minimum Space Between Tires on a Tandem Axle Trailer
- Q&A: Recommended Wire Gauge for Wiring Trailer Brakes
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Stability Control for Heavy Duty Vehicles
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Maintenance Schedule
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps