Lock For Gooseneck Coupler With Cable Release & Lever

Question

Question:

My gooseneck horse trailer has a 2-5/16 inch Fulton Gooseneck coupler w/cable release with a lever. Will this work on my trailer? 325-GH-7111

asked by: Evon H

0

Gooseneck Coupler
(click to enlarge)

Expert Reply:

Hi Evon,

Appreciate the photo, thank you, and while there is a lock option, the part number you mentioned won't work on your gooseneck coupler with the handle. There isn't a similar type of lock for the bottom of the coupler, the best have is a lock for the set screw, the Blaylock EZ Lock for Set Screw on Gooseneck Coupler # BLTL-51-40D.

expert reply by: Kyle S

0

Evon

5/1/2024

How does the Blaylock EZ Lock Set Screw Lock prevent someone from hooking up my trailer since it doesn't cover the bottom of the coupler? I am not understanding how this lock works?

Reply

Kyle S.

5/1/2024

@Evon No you do, I should've expounded the set screw lock is good for combining with the lock that goes over the bottom of the coupler. With that type of lock alone, they can just remove the inner coupler, but the set screw lock will prevent that. So it should be an addition should you have a lock that goes over the mouth of the coupler.

Reply

Evon

5/1/2024

Is there a lock that will cover that brand of coupler?

Reply

Kyle S.

5/1/2024

@Evon Unfortunately not that we offer.

Reply

Answer 1

Hey Susan, so we don't have any locks designed to lock a gooseneck coupler's inner tube to the outer tube that is welded to the trailer chassis so the best option we have would be a wheel lock like the part #288-02020 which will prevent the…

view full answer...

Answer 2

Yes the Gen-Y Auto Latch Gooseneck Coupler Lock #325-GH-7111 that you referenced would fit over a 4-1/2 inch wide hitch.

view full answer...

Answer 3

I may have another option for you but the Gen-Y Auto Latch Gooseneck Coupler Lock part #325-GH-7111 is made specifically for the Gen-Y Auto Latch Gooseneck Coupler and this isn't what you said you have so I unfortunately cannot confirm fit.…

view full answer...

Answer 4

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 5

The mounting holes on the Curt 5-Position Adjustable Channel Bracket #C48650 measure 10" center of hole to center of hole.

view full answer...

Answer 6

For your Parallax 555 model there isn't a converter replacement available. You'd have to replace the entire panel with the part #PD4560K18LS8. It does not come with breakers but in manual all of the required ones are listed from different…

view full answer...

Answer 7

To determine if the Replacement Shock for Titan Model 6 and 10 Brake Actuators, part #T1242600 will work to replace your Gabriel number 610712 (T2032) shock, you will need to verify a few quick measurements. Part #T1242600 will work as a replacement…

view full answer...

Answer 8

The Curt #C56196 2 to 3 wire taillight converter is exactly what you'll need to split out the turn signal function from the brake lamp circuit. However, keep in mind that the #C56196 is NOT compatible with LED lamps, unfortunately we don't…

view full answer...

Answer 9

To replace your JVR9000 I recommend the Jensen RV Stereo - Double DIN - AUX/USB, Bluetooth #JWM40. It has slightly different dimensions that can be easily fixed using a dash plate. This won't have a monitor to watch your video feeds from so…

view full answer...

Answer 10

The difference in tire diameter will be an additional 2-1/2 inches going from the 225/75-15 which measure 28.4 to the 235/80-16 which measure 30.9 inches. As a general rule of thumb the minimum safe distance between front and rear tires on the same…

view full answer...

Answer 11

The 3-1/4 inch diameter hole to install the part #RR5K is the correct dimension to use. We actually even had a customer come back and say they did it with a 3 inch hole saw. I attached a link to the install video you mentioned as well.

view full answer...

Answer 12

You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…

view full answer...

Lock For Gooseneck Coupler With Cable Release & Lever

Product Page this Question was Asked From

Continue Researching