Electrical Needed For Towing a Coleman Pop-up With 7-Way Behind a 2011 Acura MDX

Question

Question:

I’m looking for a 7-pin wiring harness for my 2011 Acura MDX but have only been able to find 4-pin kits on your site. Do you sell 7-pin harnesses for this vehicle? I’m looking to tow a Coleman pop-up trailer with a round 7-pin connector.

asked by: Grant G

0

Expert Reply:

The 4-Way # C56038 is going to need to be combined with the 7-Way Kit # ETBC7 you found to be able to tow your Coleman pop-up behind your 2011 Acura MDX. While we do not have a single kit for a 7-way the 4-way ties into the wiring for the brake lights, turn signals and running lights. Then the 7-way kit you found will provide the wiring for a charge line as well as a brake controller like the Redarc Liberty # RED52VR. I personally prefer this type of controller for your Acura as it only uses a small dash mounted control knob rather than a large control box mounted to the dash.

expert reply by: Bud M

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

The 4-Way #C56038 is going to need to be combined with the 7-Way Kit #ETBC7 you found to be able to tow your Coleman pop-up behind your 2011 Acura MDX. While we do not have a single kit for a 7-way the 4-way ties into the wiring for the brake lights,…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 9

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 12

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Electrical Needed For Towing a Coleman Pop-up With 7-Way Behind a 2011 Acura MDX

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching