How Many Tubes of Sealant Are Recommended for Installing an RV Roof Vent

Question

Question:

How many tubes of lap sealant will I need to seal the fan and roof?

asked by: Jeff M

0

Expert Reply:

Hey Jeff!

We have the Roof Vent Installation Kit # 344270KITW which comes with 2 tubes of sealant, a roll of butyl tape, and screws to complete the installation. If you're just needing the tubes of sealant then you can find that as part # 34427034145-1.

I'm attaching a video where we use this installation kit for a roof vent so you can see our method for applying it.

expert reply by: Jon G

0

Answer 1

I do have a solution for you. Unfortunately, it will be by replacing the lock on your RV. The red lever on your RV lock is not replaceable. We do have many options to choose from. You can use something like the Global Link RV Entry Door Locking Latch…

view full answer...

Answer 2

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 3

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 4

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

I believe I have a solution for you, but I think you may need to remeasure your cutout and/or compare the measurements of your current latch with one of ours. Since latches tend to be fairly universal in size when it comes to the RV world the Global…

view full answer...

How Many Tubes of Sealant Are Recommended for Installing an RV Roof Vent

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching