How to Measure Trailer Frame Angle for Coupler
Question:
I am looking at the Demco EZ trailer hitch coupler for A frame, welded. How do I tell whether i need a 50° or a 30° coupler?
asked by: Mark S
Expert Reply:
You'd just have to physically go out to your trailer and measure the angle. So to do this, you'd need to get a protractor or something similar and place it on the edge of the inside on one side of the trailer frame, and check to see if the other inside edge of the frame is parallel with the 50 degree line on the protractor.
50 degrees is the standard angle for trailer frames, so that's why we recommend you start there. If you do happen to have a 32 degree frame then # DM15633-81 will work great, otherwise # DM16680-52 is what you'll want.
Products Referenced in This Question
Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole and Anchors, eZ-Latch - 2-5/16" Ball - 21K
- A-Frame Trailer Coupler
- Standard Coupler
- Bolt-On
- 21000 lbs GTW
- 2-5/16 Inch Ball Coupler
- Auto Latch
- Demco
more information >
Product Page this Question was Asked From
Demco 32-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Black - 2-5/16" Ball - 21K
- A-Frame Trailer Coupler
- Standard Coupler
- Weld-On
- 21000 lbs GTW
- 2-5/16 Inch Ball Coupler
- Auto Latch
- Demco
more information >
Continue Researching
- Video: Review of Demco A-Frame Trailer Coupler - Standard Coupler - DM15633-97
- Q&A: Availability of Demco 32 Degree A-Frame Couplers with EZ Latch
- Search Results: installation videos
- Shop: Demco 32-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Silver - 2-5/16" Ball - 21K
- Shop: Demco 32-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2-5/16" Ball - 21K
- Shop: Demco 32-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Black - 2-5/16" Ball - 21K
- Video: Review of Demco A-Frame Trailer Coupler - Standard Coupler - DM15633-81
- Video: Demco A-Frame Trailer Coupler - Standard Coupler - DM15633-52 Review
- Q&A: How to Measure the Angle of Trailer A Frame To Determine if a 50 Degree A Frame Coupler will Fit
- Shop: Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K
- Search Results: 44649
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Troubleshooting 2017 Toyota Tacoma Sending Power Only to Trailer Right Side Tail Lights
- Search Results: coupler
- Video: Lippert Solera Slider Slide-Topper Review
- Shop: A-Frame Trailer Coupler - Yoke Latch - Black - 2" Ball - Weld On - 8,000 lbs
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Shop: Trailer Wiring
- Q&A: Slide Topper Recommendation for Box Width of 90.5 Inches on Gulf Stream Vintage 23BHS
- Shop: Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2-5/16" Ball - 21K
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Q&A: How to Add Tension to Solera Slide-Topper
- Search Results: 25580
- Shop: Brake Controller
- Article: Where to Position the Trailer Axle?
- Shop: A-Frame Trailer Coupler - Thumb Latch - Black - 2-5/16" Ball - Weld On - 14,000 lbs
- Shop: Fifth Wheel Hitch
- Article: RV Propane Troubleshooting | Common Propane Issues and How to Solve Them
- Search Results: dust caps