Rear Sway Bar Recommendation for 2024 GMC Sierra 2500 AT4 with 3 inch Lift

Question

Question:

What rear sway bar do you recommend for a 2024 gmc 2500 AT4 with a three inch lift?

asked by: Nate A

0

Expert Reply:

For you 2024 GMC Sierra 2500 AT4 that has a 3 inch lift I would go with the Roadmaster sway bar part # RM25FR as it's slightly thicker than the Hellwig that also fits your truck which will be helpful since lifted vehicles have a higher center of gravity.

expert reply by: Jameson C

0

Answer 1

Hellwig lists the Hellwig Rear Anti-Sway Bar #HE36MR as the correct fit for a 1998 Chevy K2500. As for fitment with the staggered shocks, you shouldn't have any issues and can even see this setup in the attached installation picture below.…

view full answer...

Answer 2

The TorkLift SuperHitch Magnum Trailer Hitch Receiver #TL74FR is the correct part for your 2023 GMC Sierra 3500. I have sent you a separate email with a PDF copy of the instructions so you can see exactly what is needed for the installation.

view full answer...

Answer 3

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 7

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 8

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Rear Sway Bar Recommendation for 2024 GMC Sierra 2500 AT4 with 3 inch Lift

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching