Can a Bearing Buddy Bearing Protector Be Used On a 7,000LB Lippert Axle With EZ Lube Grease Zerk

Question

Question:

I have 7000 lb Lippert axles with zerk fittings. Will this Trailer Buddy product fit my axles?

asked by: Kevin B

0

Expert Reply:

With your 7,000LB Lippert axles already having a zerk fitting on the end they are designed to use the Grease Cap # TRU66FR to easily access the grease zerk. While the Bearing Buddy Bearing Protectors 1.98" # BB1980A are to small for your hub we do have the 2.717" # BB27SR for your hub size. This will generally require you to remove the grease zerk from the end of your spindle to use.

expert reply by: Bud M

0

Answer 1

The Dexter Trailer Hub #DX46XR uses a 2.72" grease cap. We do sell a cap in this size. For that I recommend the Trailer Hub Grease Cap #TRU66FR. This cap is made for an easy-lube axle, so it includes the cap and the removable rubber plug.

view full answer...

Answer 2

The correct grease cap for the Dexter Trailer Hub and Drum Assembly for 8,000-lb E-Z Lube Axles #DX46XR is the #TRU66FR.

view full answer...

Answer 3

For a 5,200 lb trailer axle hub with 6 lugs the correct size dust cap/cover is 2.44 inches like the TruRyde cover part #DC250L-DCRP. Sounds like what you ordered was the version for the 8 lug hubs which is a slightly larger size.

view full answer...

Answer 4

We can help you determine the correct replacement hub assembly for your boat trailer. In order to find the correct replacement hubs for your trailer you need to know the weight rating of your axle, and also what bearings your current hub has. You…

view full answer...

Answer 5

An 8-285 hub does not have the correct bearings or races to work with Bearing Buddies, so you would need to use a standard grease cap. For example, the #8-285-11 hub and drum needs Trailer Hub Grease Cap #TRU66FR for a quantity of one or #RG04-120…

view full answer...

Answer 6

You'll need a new center cap. The cap you need will depend on the pilot diameter of the wheel, which is the large hole the center cap fits into. Pull one wheel, and measure the wheel's pilot diameter. A 6 lug wheel like what's shown in…

view full answer...

Answer 7

To measure for a grease cap you will need to use something that can provide a very accurate measurement such as dial or digital calipers. Then you will measure the diameter at the center of the hub where the grease cap will fit. Grease cap…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Can a Bearing Buddy Bearing Protector Be Used On a 7,000LB Lippert Axle With EZ Lube Grease Zerk

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching