Ramp Set to Load Side by Side onto 36 inch Tall Trailer

Question

Question:

What length ramp would I need to load a side by side thats wheelbase is 114 and the ground clearance is 14. Vehicles total weight 3,000 pounds and the trailer is 36 ground to deck?

asked by: James G

0

Expert Reply:

I would think a 72 inch long set like the part # 288-07503 would work great. This has a 6k capacity and would make loading on your trailer pretty easy. See attached picture.

expert reply by: Jameson C

0

ATV and Ramp
(click to enlarge)

Answer 1

I believe you are referring to the 1" prongs on the Stallion Aluminum Car Hauler Ramp Set #288-07503 that are designed to grab onto the small gap at the end of most trailers. This not only provides a secure connection when loading/unloading, but…

view full answer...

Answer 2

The Stallion #288-07503 loading ramps are manufactured in China. For a US made alternative, check out the Gen-Y Hitch Heavy Duty Aluminum ramp set which measure 72 x 14 inches which we offer as part #325-GH-R72. I've linked to a demonstration…

view full answer...

Answer 3

The rungs on the Stallion Loading Ramp Set #288-07489 that you referenced have 3" gaps between them as you can see in the attached photo. My contact at Stallion confirmed this. If the spacing is too much for you to use and the 3,000 lbs weight…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 10

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Answer 11

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Answer 12

There are going to be two parts to the handle that you will need to operate the Lippert Components Spare Tire Winch part #LC159056. The first of which is the intermediate shaft or what Lippert calls a Crank Extension part #LC1315411. This will be…

view full answer...

Ramp Set to Load Side by Side onto 36 inch Tall Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching