What Type Of Grease Are The Bearings Packed With On Trailer Idler Hub Assembly # AKIHUB-545-2-2K?

Question

Question:

What kind / type of grease do you folks use to pack these hubs?

asked by: Steve

0

Expert Reply:

The Trailer Idler Hub Assembly # AKIHUB-545-2-2K comes with the bearings packed with a Lithium complex, multipurpose grease. You must make sure to use another lithium complex grease like the Grease # L11390. It does not have to be the same color, you only need to ensure the grease has a lithium complex.

expert reply by: Bud M

0

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

LMX Red grease like the part #L11390 is compatible with the grease that is in trailer hub part #AKIHUB-545-2-2K that you referenced and would work great.

view full answer...

Answer 3

I went to the warehouse and measured the #AKIHUB-545-2-2K you asked about. I have attached a photo of the hub with the dimension you asked for. The hub depth outside to outside is 4 inches. This is an idler hub assembly for 2,000-lb axles and will…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 12

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

What Type Of Grease Are The Bearings Packed With On Trailer Idler Hub Assembly # AKIHUB-545-2-2K?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching