Grease to Use with Trailer Hub # AKIHUB-545-2-2K that is Pre Packed with Grease

Question

Question:

What grease is compatible with the grease that is pre packed in the bearings for maintenance down the road?

asked by: Alex

0

Expert Reply:

LMX Red grease like the part # L11390 is compatible with the grease that is in trailer hub part # AKIHUB-545-2-2K that you referenced and would work great.

expert reply by: Jameson C

0

Answer 1

I went to the warehouse and measured the #AKIHUB-545-2-2K you asked about. I have attached a photo of the hub with the dimension you asked for. The hub depth outside to outside is 4 inches. This is an idler hub assembly for 2,000-lb axles and will…

view full answer...

Answer 2

The Trailer Idler Hub Assembly #AKIHUB-545-2-2K comes with the bearings packed with a Lithium complex, multipurpose grease. You must make sure to use another lithium complex grease like the Grease #L11390. It does not have to be the same color, you…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 5

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

On a single axle trailer you will want to have a hanger spacing of around 22-3/4 inches when using the 23-1/8 inch long Double-Eye Spring #e59SR. This will allow that rear shackle to correctly lean away from the axle for proper suspension travel.

view full answer...

Grease to Use with Trailer Hub # AKIHUB-545-2-2K that is Pre Packed with Grease

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching