Solution for Replacement Parts for Fulton T1802 Winch

Question

Question:

Good morning I would like to replace the part for my trailer winch t1802 1800lbs

asked by: Angelo B

0

Expert Reply:

The Fulton T1802 was discontinued quite a while ago. Unfortunately, this means that replacement parts for the winch are no longer around. The best solution is to replace it with a similar winch like the Fulton Single Speed Trailer Winch - 1,800 lbs # F142306.

I have attached an installation video below for your reference.

expert reply by: Robin H

0

Fulton T1802
(click to enlarge)

Answer 1

I have a solution for you. The Fulton Single Speed Trailer Winch - 10" Long Handle, w/ 20 FT Strap - 1,800 lbs, #F142306, is the winch I recommend for your application. This winch uses a 2-way ratchet system and has a solid drum design which is…

view full answer...

Answer 2

The repair kit for a Fulton T1802 (which included the pawl) used to be available but was discontinued a number of years ago, and the pawl itself is not available separately. So really the best option we have is to replae the winch with a new one, the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Solution for Replacement Parts for Fulton T1802 Winch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching