Can a Bent Landing Gear Foot Pad Be Used With a SnapPad?

Question

Question:

Hello, I am looking at purchasing a set of snap pads for my 2013 forest river Georgetown class A motor home. One of my pads is bent I bought motor home used and was already bent. Will the snap pads still work if one is bent or will the pad have to be replaced for a secure fit? Thank you for your time and help.

asked by: Brian W

0

Expert Reply:

The feet on your motorhome's landing gear should not be bent at all, and for a SnapPad like the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet # SP54FR4 you're looking to fit, it's going to need to be replaced.

For instance, if you had a Lippert Landing Gear and needed a replacement 9" foot to work with the SnapPads mentioned above, you'd need the Lippert 5th Wheel RV Landing Gear Foot Pad # LC314667.

expert reply by: Bryce D

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 5

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 6

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 7

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 8

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

It's very easy to install a trailer brake controller on a 2021 Honda Ridgeline. I recommend the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 which comes with a harness that you could simply attach to the one that came with the…

view full answer...

Can a Bent Landing Gear Foot Pad Be Used With a SnapPad?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching