How to Determine if 6k Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange Will Fit Flange

Question

Question:

Hello, How do I know if item 23-105-09 will fit my backing plate? This is an old axle of unknown manufacture. It’s so old it has the Warner electromagnetic brakes on it. Thank you!

asked by: David

0

Expert Reply:

You'll need to do some quick measuring of your backing plate/brake flange to see if you can use the 6,000 lb Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand # 23-105-09.

I have added photos below that I hope will help. One is of a standard 5-bolt brake flange where the bolts are 2-1/8" apart except for the bottom which are 3" apart. The other photo is of is the brake assembly which shows the dimensions of the AL-KO/Hayes 4-bolt flange, where the holes are 3-1/8", 2-1/2" and 3-3/8" apart.

Hopefully this helps you determine if you can use the # 23-105-09, and if you can and also need the right hand side that part number is # 23-106-09.

expert reply by: Kyle S

0

5-Bolt Brake Flange Measurement
(click to enlarge)

AL-KO/Hayes 4-Bolt Brake Flange Measurement
(click to enlarge)

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 3

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 4

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

How to Determine if 6k Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange Will Fit Flange

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching