Inside Trailer Width Needed to Install Storage Trunk for Malone MicroSport and XtraLight Trailers

Question

Question:

I see the answers for the width- 37 3/4 for the box. Id like to know what the total distance is between the mounting plates, not just the box but the required room needed to mount. Trying to see if it will fit the Northern Tool trailer that I have Malone bars on, thanks.

asked by: JAndrew

0

Expert Reply:

The mounting brackets that come with the Storage Trunk for Malone MicroSport and XtraLight Trailers # MPG481 will add about 1/2" to either side (keep in mind some of that mounting bracket is installed under the frame) so altogether you need about 38-3/4" in -between the trailer frame to install this kit.

expert reply by: Jon G

0

Answer 1

I couldn't find too much information regarding the part numbers that you referenced besides that those storage containers have wheels, their storage capacity, and that they came with straps to secure the containers. What sets the Storage Trunk…

view full answer...

Answer 2

We have one box that fits the Malone Microsport trailers with the part #MPG481 which installs below the bars of the rack. I attached a review video and picture for you to check out as well.

view full answer...

Answer 3

Thank you for reaching out! The top of the lid for the Storage Trunk for Malone MicroSport and XtraLight Trailers #MPG481 is going to sit roughly 10" above the trailer frame according to my contact at Malone. I've attached a review video for…

view full answer...

Answer 4

The widest portion of the #MPG475 that you referenced excluding the crossbar is 53-15/16 inches. Including the bar it's 78 inches.

view full answer...

Answer 5

The U shape below the crossbars on the Malone Crossbar Conversion #MPG475 is 45" wide.

view full answer...

Answer 6

You'll be pleased to hear the base of the: -Malone Crossbar Conversion Kit for Standard Utility Trailer #MPG475 measures 32" before the bar starts to curve upwards. I have also attached an image showing this measurement for you to check…

view full answer...

Answer 7

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Inside Trailer Width Needed to Install Storage Trunk for Malone MicroSport and XtraLight Trailers

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching