Replacement Trailer Hitch Options for a 2008 Coachmen Cross Country 38' Motorhome
Question:
I have a 2008 Coachmen Cross Country 38 foot coach on a Freightliner chassis and the original hitch rated for 5000# GTW failed. I am looking at this hitch ,but it would have to be attached horizontal instead of vertical on the frame. Is this an acceptable change, and if so would it affect the GTW of the hitch? The first photo is of the original hitch and the others are the rear passenger side of the frame showing the attachment points. If this hitch can be attached in a horizontal mode, I would go to a longer hitch.
asked by: H C
Helpful Expert Reply:
The mounting brackets on the Curt Class 5 Universal Weld-on Hitch # C47CR do need to be in that upright position so while this hitch can technically fit with your motorhome chassis, you'll need to get creative on how to properly weld the brackets to the frame.
For an alternative option with the brackets that are in the same orientation as your frame brackets I recommend the Multi-Fit Motorhome Trailer Hitch # 5350 which fits 24" - 46" wide frames and is rated for 5,000 lbs towing.
If you want the higher weight rating go with the Curt, but if you want the matching frame setup go with the Draw-Tite.
Products Referenced in This Question
Multi-Fit Motorhome Trailer Hitch, 24" - 46" wide
- RV and Camper Hitch
- Frame Mount Hitch
- 24 - 46 Inch Wide Frame
- 500 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Bolt-On
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1600 lbs TW
- 16000 lbs GTW
- Class V
- 2 Inch Hitch
- 9 Inch Drop
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Suspension Enhancement
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide
- Shop: Trailer Hitch
- Shop: Vehicle Sway Bars
- Search Results: sumosprings
- Shop: Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Front Axle
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 44" Wide
- Shop: Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop
- Shop: Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle
- Shop: Buyers Products Class 4 Service Body Long Hitch Receiver - Accepts All 2" Hitch Accessories
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 62" Wide
- Video: Buyers Products Heavy Duty Truck Hitch - Weld-On Hitch - 3371801055 Review
- Video: Review of CURT Heavy Duty Receiver Hitch - Weld-On Hitch - C37CR
- Search Results: koni shocks
- Search Results: airbag
- Search Results: air bag suspension
- Search Results: weld on receiver hitch
- Shop: Fluid Filters
- Video: Dexter Trailer Springs Over-Under Conversion Kit Installation
- Q&A: Can Square Axle Trailer Have Axle Moved Below Leaf Spring
- Q&A: 2-1/2 Inch Shackle Straps Are Flipping After Replacing Leaf Springs
- Q&A: Can Shocks of Trailer be Used with Dexter Over Under Kit
- Q&A: Availability of Suspension Upgrade Kit for Tandem Axles With 36 Inch Spacing
- Q&A: How To Raise a Trailer Without Flipping Axle
- Q&A: Vintage Trailer Suspension Replacement Recommendations
- Video: Curt Hitch Fabrication Parts - Receiver Tube - E17 Review
- Video: Review of Draw-Tite Heavy Duty Receiver Hitch - Weld-On Hitch - 41990
- Q&A: Wet Suspension Bolt vs a Regular Suspension Bolt
- Shop: Bumpers
- Shop: Wheel Liners