Do You Offer The Buckle Separately From The Replacement Tie-Down for Extang Solid Fold 2.0?

Question

Question:

Do you sell just the buckle for the Extang Solid Fold 2.0 Hard Tonneau Cover replacement tie down?

asked by: Vernon

0

Expert Reply:

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers # EX1024 is the only way we sell the buckle as that is the only way Extang offers these parts.

expert reply by: Bud M

0

Answer 1

Based on your images it appears you have a BAKFlip Tonneau Cover. This will use the Buckle and Strap Conversion Kit #PARTS-356A0009. The Replacement Tie-Down #EX1024 you found is for Extang Solid Fold 2.0 Hard Tonneau Covers which are only 3 panels.

view full answer...

Answer 2

Thanks for the picture! Wthout knowing for sure what model tonneau cover you have, I can't say for sure. However, it does look like this strap will be compatible with your tonneau cover. As long as you have the 83-XXX series Extang Solid Fold 2.0…

view full answer...

Answer 3

First you will need to determine if you have the Extang Solid Fold 1 or 2.0 on your 2014 Ford F-150, as the update occurred right at the same timeframe your F-150 was made. The best way to tell the difference is by the release handles on the tailgate…

view full answer...

Answer 4

The Replacement Female Tie-Down Buckle for Extang SolidFold Tonneau Covers #EX1018 is the only way to get the buckle for the original Extang SolidFold covers. We do have the Replacement Female Tie-Down Buckle for Extang SolidFold 2.0 Tonneau Covers…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Do You Offer The Buckle Separately From The Replacement Tie-Down for Extang Solid Fold 2.0?

Product Page this Question was Asked From

Continue Researching